| 03/05/2026 10:54 AM |
Rick VanHatten |
Joni, What is needed would be listed here |
Supplies |
In Service |
|
2,981 |
| 03/04/2026 06:31 PM |
Ron Prater |
M17 bandsaw does not turn on the dust collector |
Band Saw Jet 14 Inch M17 |
Limited Functionality |
|
2,980 |
| 03/04/2026 04:13 PM |
Nels Lundgren |
Installed 3/8″ bandsaw blade on M02. Adjusted the blade guides for the larger blade. Rick or Dana can check my work. Put signage on the bandsaw to indicate 3/8″ blade installed.
Earlier it was reported that they could not turn off the saw and needed to unplug it. I did not find that to be the case. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,979 |
| 03/04/2026 07:53 AM |
Michael Ross |
The blade broke. I tried to turn off the machine. the stop button didn’t work, the emergency button did not turn the machine off. I had to unplug the machine to get the wheel to stop spinning. |
Band Saw 14-3000 Laguna M2 |
Out of Service |
|
2,978 |
| 03/03/2026 05:18 PM |
Jerry Mackelburg |
To facilitate troubleshooting the intermittent problems with the automatic blast gate, the blast gate’s slider was replaced with one that would allow adequate airflow in either the “Open” or “Closed” state of the gate. So, the blast gate is effectively always open regardless of what its controller thinks/reports. However, for dust collection to be effective, it may be necessary to turn the Oneida system on (with the Green pushbutton switch on its control panel). |
Planer 16 Inch Laguna 5HP M45 |
Limited Functionality |
Yes |
2,977 |
| 03/03/2026 05:01 PM |
Jerry Mackelburg |
The lift leadscrew and guides were cleaned and lubricated with GOO GONE to enable smother noise free operation. But one of the brass nuts that sets the leadscrew tension to control backlash is loose, which probably isn’t ideal. |
Router Table #2 Rockler M31 |
In Service |
|
2,976 |
| 03/02/2026 05:47 PM |
Rick VanHatten |
Test of Shop Log for Credit Card Payment – Would enter name of person making payment, amount and what its for. Routes to Pete Sterling and cc to Dallas, Nels & Tom |
Credit Card Payment – Zelle |
In Service |
|
2,975 |
| 03/01/2026 09:26 AM |
Jerry Mackelburg |
The new fence is really nice, but the lift apparently needs attention (cleaning, lubrication, and/or/?) It’s making nasty noises when adjusted. |
Router Table #2 Rockler M31 |
Limited Functionality |
|
2,974 |
| 02/28/2026 08:31 PM |
Jerry Mackelburg |
The feed problem reported last week in Rpt. No. 2945 could not be replicated today. But there was a one-inch-wide path of really sticky residue on the table (that cleaned off easily with GOO GONE) that may have been somewhat responsible. Both table rollers rotated freely so neither is now jammed with debris – which has caused this type of problem in the past. Another possibility is that the initial cut depth was not properly set based on the thickest part of the workpiece as recommended. |
Planer 20 Inch General International M29 |
In Service |
|
2,973 |
| 02/27/2026 02:06 PM |
Rick VanHatten |
Adjusted tracking. Ran for over an hour and kept adjusting tracking so it did not drift. Worn bearings were replaced earlier. There is about an inch + of conveyor belt cut off because a abrasion, which is fine. No need to replace belt at this time. There is a spare in the bench room. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,972 |
| 02/27/2026 02:03 PM |
Rick VanHatten |
Miss reported as worn bearings that were actually on M11 |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,971 |
| 02/26/2026 11:13 AM |
Edee Armand |
NEED BANDAIDS IN FIRST AID KIT |
Not a Tool Repair Issue |
|
|
2,970 |
| 02/26/2026 08:30 AM |
Rick VanHatten |
Moved to former lathe area |
Router Table #2 Rockler M31 |
In Service |
|
2,969 |
| 02/26/2026 08:30 AM |
Rick VanHatten |
Moved to former lathe area |
Router Table #1 M30 |
In Service |
|
2,968 |
| 02/26/2026 08:29 AM |
Rick VanHatten |
Moved to former lathe area |
Disk/Belt Sander Jet M38 |
In Service |
|
2,967 |
| 02/26/2026 08:28 AM |
Rick VanHatten |
Moved to former lathe area |
Belt/Disk Sander Jet M6 |
In Service |
|
2,966 |
| 02/26/2026 08:27 AM |
Rick VanHatten |
Moved to former lathe area |
Spindle Sander Powermatic M34 |
In Service |
|
2,965 |
| 02/26/2026 08:27 AM |
Rick VanHatten |
Moved to former lathe area |
Spindle Sander Enlon M33 |
In Service |
|
2,964 |
| 02/26/2026 08:25 AM |
Rick VanHatten |
Mortiser is now located in the back corner where the lathes used to be |
Mortiser Powermatic M27 |
In Service |
|
2,963 |
| 02/26/2026 08:23 AM |
Rick VanHatten |
Works now |
Jointer 16 Inch Grizzly M12 |
In Service |
|
2,962 |
| 02/26/2026 08:22 AM |
Rick VanHatten |
Replaced with new Tormek from the Grogan Estate. |
Sharpening System Tormeck |
In Service |
|
2,961 |
| 02/25/2026 05:51 PM |
Jeff Bratt |
Observation abut miter saw dust collector – it wasn’t working. Turns out the lid for the cyclone was not on tight, so there was essentially no suction or airflow through the hose to the saw. The dust chute right behind the blade was completely clogged and sawdust was flying everywhere. Got the lid on right and cleaned up all the extra sawdust. Just something to be aware of. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,960 |
| 02/25/2026 05:33 PM |
Jeff Bratt |
I got the sander running again. The drive belt was way off track, and about 1/2″ of one whole edge was shredded. There is still a piece of the drive belt stuck under the bed. It should actually work now, we’ll have to decide if a new drive belt is needed or not. |
Drum Sander 25 Inch Supermax M11 |
Limited Functionality |
|
2,959 |
| 02/25/2026 03:30 PM |
John Goodrich |
belt driving stock is off rollers and slipping, thus not moving the stock into the sanding drum |
Drum Sander 25 Inch Supermax M11 |
Out of Service |
Yes |
2,958 |
| 02/25/2026 11:34 AM |
Rick VanHatten |
Modified naming of original Robust to “Lathe 20 Inch (M25)” to “Lathe Long Bed Robust (M25) to match naming of the “Lathe Short Bed Robust (M24) |
Lathe Long Bed Robust M25 |
In Service |
|
2,957 |
| 02/25/2026 11:30 AM |
Rick VanHatten |
Added Short Bed Robust (M24) to the Log |
Lathe Short Bed Robust M24 |
In Service |
|
2,956 |
| 02/24/2026 02:50 PM |
Tom Bamburg |
conveyer belt bushing replaced all bushings lubed (boshield T9). Trimmed outboard end of conveyer belt. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,955 |
| 02/24/2026 08:43 AM |
Paul Schankin |
AC cord checked, AC plug termination had signs of chaffing, did new termination and check OK. Machine in service. |
Shop Vac Rigid |
In Service |
|
2,954 |
| 02/23/2026 08:34 PM |
Steve Carter |
Member received a shock while using, I had used it earlier without incident |
Shop Vac Rigid |
Out of Service |
|
2,953 |
| 02/23/2026 07:53 PM |
Dana Chapin |
Repaired fence |
Band Saw 18 Inch Laguna M1 |
In Service |
|
2,952 |
| 02/21/2026 02:57 PM |
Michael Ross |
the mortiser was removed from the mobile base and placed on the floor |
Mortiser Powermatic M27 |
Out of Service |
|
2,951 |
| 02/21/2026 02:55 PM |
Mark Umphres |
need to restock AAA batteries in 12D bench room supply. Also Replace wixey batteries drawer 1A table saw 2 |
Supplies |
|
|
2,950 |
| 02/21/2026 01:20 PM |
Rick VanHatten |
Added 6th PSI Lathe to Shop Log & removed Jet |
Lathe PSI – 10 Inch M44 |
In Service |
|
2,949 |
| 02/21/2026 01:19 PM |
Rick VanHatten |
Added Grogan Powermatic Lathe to Shop Log |
Lathe Powermatic M50 |
In Service |
|
2,948 |
| 02/20/2026 04:43 PM |
Nels Lundgren |
Bearing on conveyor is worn out and conveyor belt has travelled to the side and abraided. I think the belt can be salvaged, but need to replace the bearing first. |
Drum Sander 25 Inch Supermax M10 |
Out of Service |
|
2,947 |
| 02/20/2026 11:13 AM |
Michael Ross |
5″ discs were made. In the future contact me for more discs |
Drill Press 18 Inch Delta M9 |
In Service |
|
2,946 |
| 02/20/2026 11:10 AM |
Michael Ross |
wood gets hung up on the rollers. then you have to back the height off to get the wood out |
Planer 20 Inch General International M29 |
Limited Functionality |
|
2,945 |
| 02/19/2026 07:51 PM |
Nels Lundgren |
Out of 5×30 dominos. None left in the systainer. |
Supplies |
|
|
2,944 |
| 02/19/2026 09:48 AM |
Paul Schankin |
Installed gasket under lid of left hand bin to improve dust collection between bins. Monitor for efficiency. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,943 |
| 02/19/2026 09:29 AM |
Paul Schankin |
DC bag changed, bag was at 90% full. |
Shop Vac Rigid |
In Service |
|
2,942 |
| 02/18/2026 05:57 PM |
Jeff Bratt |
Resaw bamdsaw – fence is not working. While it looked good at first, it is delicate and can no longer hold its position. We should go back to the old fence or get something more robust. |
Band Saw 18 Inch Laguna M1 |
In Service |
|
2,941 |
| 02/17/2026 04:34 PM |
Jerry Mackelburg |
OOPs Rpt. No. 2938 was intended for the Miter Saw.🤔 |
Mortiser Powermatic M27 |
In Service |
|
2,940 |
| 02/17/2026 04:30 PM |
Jerry Mackelburg |
Additional Baltic Birch fences were provided to better support bevel cuts. They’re in the left accessory drawer adjacent to the saw. They’re intended to serve as temporary substitutions for the miter/straight cut fences normally installed. Extensive laser engravings were added to all four fences in an attempt to maximize their utility and survivability. Table stop blocks were added to the tracks on both sides of saw. They can be easily repositioned (without removal) when not needed. The two fence stop blocks should be kept in the accessory drawer along with the additional vertical vise and horizontal vise when not needed. The extraneous stuff that was in that drawer was placed in a box in Bench Room Drawer 14A. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,938 |
| 02/17/2026 04:29 PM |
Jerry Mackelburg |
Additional Baltic Birch fences were provided to better support bevel cuts. They’re in the left accessory drawer adjacent to the saw. They’re intended to serve as temporary substitutions for the miter/straight cut fences normally installed. Extensive laser engravings were added to all four fences in an attempt to maximize their utility and survivability. Table stop blocks were added to the tracks on both sides of saw. They can be easily repositioned (without removal) when not needed. The two fence stop blocks should be kept in the accessory drawer along with the additional vertical vise and horizontal vise when not needed. The extraneous stuff that was in that drawer was placed in a box in Bench Room Drawer 14A. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,939 |
| 02/17/2026 03:43 PM |
Rick VanHatten |
Take off rolling base. Was on it just to move |
Mortiser Powermatic M27 |
In Service |
|
2,937 |
| 02/17/2026 02:01 PM |
Nels Lundgren |
Need more 5″ round sacrificial inserts for the drill press tables |
Drill Press 14 Inch Powermatic M8 |
In Service |
|
2,936 |
| 02/17/2026 12:28 PM |
Rick VanHatten |
Placed in Service |
Band Saw Jet 14 Inch M17 |
In Service |
|
2,935 |
| 02/16/2026 03:33 PM |
Bryan Blacksher |
Josh Toschi reported that the large laser (right side) would not cut through a 3mm piece of baltic birch. |
Laser Thunder Nova 51 M19 |
Limited Functionality |
|
2,934 |
| 02/15/2026 12:29 PM |
Nels Lundgren |
Large engineering square made it back to the tool wall, but 2nd Wixey still MIA |
Not a Tool Repair Issue |
|
|
2,933 |
| 02/14/2026 08:58 PM |
Jerry Mackelburg |
The machine moves around with use because it’s on a dolly with casters that don’t lock. |
Mortiser Powermatic M27 |
Limited Functionality |
|
2,932 |
| 02/14/2026 08:52 PM |
Jerry Mackelburg |
I discouraged a member from using the Tormek on her expensive tools today because I wasn’t sure if the problem reported in December (Rpt, No. 2808) had been resolved. Has it? |
Sharpening System Tormeck |
Limited Functionality |
|
2,931 |
| 02/14/2026 12:48 PM |
Dana Chapin |
Cleaned blade |
Band Saw 18 Inch Laguna M1 |
In Service |
|
2,930 |
| 02/14/2026 11:38 AM |
Duane Kuperus |
Lou Cortelinni and I adjusted the extension table on the #2 table saw to bring it more level to the table. It is evident that the extension table has a sway in the middle and my require replacement to get it perfectly flat. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,929 |
| 02/14/2026 10:57 AM |
Skip Florey |
Replaced blade on tool # M03. 2 111″ blades left in inventory |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,928 |
| 02/14/2026 10:04 AM |
Skip Florey |
Band saw blade bad |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,927 |
| 02/12/2026 09:47 PM |
Nels Lundgren |
Missing one wixey and missing one large engineering square from tool wall |
Not a Tool Repair Issue |
|
|
2,926 |
| 02/10/2026 09:33 PM |
Jerry Mackelburg |
New wooden fences were installed to improve the saw’s safety and performance. Like the previous versions, which were destroyed after 1.5 years of use, they’re easy to adjust and can provide near zero fence clearance for straight and miter cuts without being cut/sacrificed. Like before, they should be temporarily removed or slid out of the cut path for bevel cuts. https://groups.google.com/a/sdfwa.org/g/sdfwa-shift-supervisors/c/tqCVBvesesg/m/8QTfEUFRBAAJ |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,925 |
| 02/09/2026 04:26 PM |
Nels Lundgren |
set the blade to table angle to 90 degrees and added locking nut to the bolt that stops the bandsaw table at 90 degrees to the blade. This bolt is a M6 1.00 thread. Had to get it at Marshall’s, so I got 10 for 65cents and used the change n my truck.
In the process, discovered the blade guard was difficult to raise and when raised it was contacting the inside of the top wheel, so care must be taken when changing a blade that the guard is reinstalled such that it does not interfere with the top wheel. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,924 |
| 02/08/2026 04:20 PM |
Jerry Mackelburg |
Yesterday a member had a problem with a 1/2″ straight router bit being pulled up during use. The workpiece grain structure looked like it would try to do that. He claims to have done everything correctly so, assuming everything is working properly on the lift, it seems most likely that bit slipped in the collet (dirty/worn?). Better? collets like those used on CNC spindles are available for those Porter Cable routers that might work better if they’re kept clean. https://www.precisebits.com/products/equipment/porter-cable_0429_kits.asp&filter=1 |
Router Table #2 Rockler M31 |
In Service |
|
2,923 |
| 02/08/2026 04:13 PM |
Jerry Mackelburg |
A member reported that he previously (during an epoxy class) had a problem with an 1/8″ round over bit being pulled up during use even though he claimed to have done everything correctly. He tried it again yesterday apparently without any issues. Assuming everything is working properly on the lift, it seems most likely that bit slipped in the collet (dirty/worn?). Better? collets like those used on CNC spindles are available for those Porter Cable routers that might work better if they’re kept clean. https://www.precisebits.com/products/equipment/porter-cable_0429_kits.asp&filter=1 |
Router Table #1 M30 |
In Service |
|
2,922 |
| 02/07/2026 09:16 PM |
Jerry Mackelburg |
The extension table is not properly aligned vertically with the saw’s tabletop and extension wing. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,921 |
| 02/07/2026 09:14 PM |
Jerry Mackelburg |
The extension table is not properly aligned vertically with the saw’s top table and extension wing. |
Table Saw 10 Inch #1 Sawstop Industrial 5HP M35 |
In Service |
|
2,920 |
| 02/07/2026 09:00 PM |
Jerry Mackelburg |
Automatic blast gate not operating reliably. Removed slider, fortunately the note about the workaround had not been removed this time (see Rpt. No. 2905). |
Planer 16 Inch Laguna 5HP M45 |
Limited Functionality |
Yes |
2,919 |
| 02/07/2026 07:45 PM |
Nels Lundgren |
Replaced blade on miter saw with one from home. Cuts much improved and seems to cut square now. Hmmmmmm |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,918 |
| 02/07/2026 06:09 PM |
Nels Lundgren |
The Cyclone does not come on when operating the 16 inch jointer. Needs to be operated manually |
Jointer 16 Inch Grizzly M12 |
Limited Functionality |
Yes |
2,917 |
| 02/07/2026 01:35 PM |
Duane Kuperus |
sand belt cover latch button is missing. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,916 |
| 02/07/2026 12:12 PM |
Duane Kuperus |
when fence is tightened down, the fence is no longer square to the table. needs adjustment |
Band Saw 18 Inch Laguna M1 |
Limited Functionality |
|
2,915 |
| 02/07/2026 12:11 PM |
Duane Kuperus |
Replaced blade on the #1 Table saw. Cleaned the blade and returned to the blade cabinet for use. |
Table Saw 10 Inch #1 Sawstop Industrial 5HP M35 |
In Service |
|
2,914 |
| 02/07/2026 11:29 AM |
Duane Kuperus |
Drum cover latch missing |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,913 |
| 02/07/2026 11:09 AM |
Duane Kuperus |
Dust collection giving false high level reading. Checked drum level and found right drum 1/8 full and left drum empty. The drum top was not firmly in pace due to deformed drum. Suspect this was the cause of false alarm indication. Still need to replace the drums. Correctly replaced the drum cover. Amber light cleared. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,912 |
| 02/07/2026 10:59 AM |
Duane Kuperus |
Auto blast gate does not open automatically |
Band Saw 18 Inch Laguna M1 |
In Service |
|
2,911 |
| 02/07/2026 10:53 AM |
Duane Kuperus |
Replaced sand paper |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,910 |
| 02/05/2026 09:58 PM |
Rick VanHatten |
Cyclone was starting and continuously ran. Found Input #23 shorted. Cut the input wire and works fine. Found a cut unlabeled wiring on the drops to the Drum Sanders. Not sure if that was the input. Need input-Tool Index table in the cabinet to be able to trouble shoot inputs |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
2,909 |
| 02/05/2026 10:03 AM |
Lynn Welling |
the latch pin on the drum sander M11 fell off. Looks like it needs a retaining clip. the knob and spring are in the top drawer of the sup station. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,908 |
| 02/03/2026 02:41 PM |
Rick VanHatten |
When resawing stock can catch on table when leaving the inset (inset = black piece surrounding the blade) after cut. Mike Boucher |
Band Saw 18 Inch Laguna M1 |
Limited Functionality |
|
2,907 |
| 01/31/2026 09:24 PM |
Jerry Mackelburg |
The Wixey DRO needed to be reset again! |
Planer 20 Inch General International M29 |
In Service |
|
2,906 |
| 01/31/2026 09:22 PM |
Jerry Mackelburg |
If this sounds like a repeat, it’s because it is – see Rpt. No. 2887 from the 21st 🤷♂️ “The blast gate’s acrylic slider was removed to essentially keep the gate “open” all the time. But user’s need to still need to ensure that the dust collector is on for dust collection to work. Signage was added to the start/stop switch accordingly. Maybe it can stay there this time until the problem gets corrected [and properly tested]?”🤔 The Wixey gauge needed to be reset again! |
Planer 16 Inch Laguna 5HP M45 |
Limited Functionality |
Yes |
2,905 |
| 01/31/2026 09:12 PM |
Jerry Mackelburg |
Cleaned sawdust out of the cabinet, connected internal dust hose, and closed blade access dust chute door. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,904 |
| 01/29/2026 05:59 PM |
Nels Lundgren |
TS #1 is in service. I suspect someone cycled the power switch above the paddle switch and cleared the problem. |
Table Saw 10 Inch #1 Sawstop Industrial 5HP M35 |
In Service |
|
2,903 |
| 01/29/2026 11:12 AM |
Oi Ling Kwan |
Saw blade will not turn when saw is switched on (green light blinks and red light solid) |
Table Saw 10 Inch #1 Sawstop Industrial 5HP M35 |
Out of Service |
|
2,902 |
| 01/29/2026 11:08 AM |
Oi Ling Kwan |
Table saw #1 blade will not turn when saw is switched on. (blinking green, solid red lights) |
Table Saw 10 Inch #1 Sawstop Industrial 5HP M35 |
Out of Service |
|
2,901 |
| 01/28/2026 06:56 PM |
Ron Prater |
Blast gate valve on the Laguna planer doesn’t open. In manual use now. |
Planer 16 Inch Laguna 5HP M45 |
Limited Functionality |
Yes |
2,900 |
| 01/26/2026 02:47 PM |
Gordon Stone |
HDM CnC Z registration 2.9mm too low |
CNC Shapeco HDM M4 |
Out of Service |
|
2,899 |
| 01/25/2026 02:06 PM |
Nels Lundgren |
Changed paper on Drum Sander M10 |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,898 |
| 01/24/2026 01:43 PM |
Jerry Mackelburg |
Outfeed bed roller was jammed with wood wedge preventing proper material feed. Cleaned everything, applied Boeshield T-9 to tables and bed rollers, and adjusted bed rollers. |
Planer 20 Inch General International M29 |
In Service |
|
2,897 |
| 01/24/2026 10:58 AM |
Duane Kuperus |
Need new dust collection drums in the dust collection system. The existing drums are warped, bent and very hard to close and seal. |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
2,896 |
| 01/24/2026 10:54 AM |
Dan McNaughton |
Need new dust drums outside!! |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,895 |
| 01/24/2026 09:59 AM |
Dan McNaughton |
Dumpster was not locked when I arrived at 7:30am Sat Jan 24 2026 |
Not a Tool Repair Issue |
|
|
2,894 |
| 01/24/2026 08:40 AM |
Paul Schankin |
Ref 2888. Power cords improperly plugged into wrong outlets. Rewired, checked out, machine in service. |
Drum Sander 25 Inch Supermax M11 |
In Service |
Yes |
2,893 |
| 01/23/2026 09:08 PM |
Tom Roetker |
belt disc saner blast gate not working |
Belt/Disk Sander Jet M6 |
In Service |
Yes |
2,892 |
| 01/23/2026 09:07 PM |
Tom Roetker |
general planer is not feeding wood |
Planer 20 Inch General International M29 |
Out of Service |
|
2,891 |
| 01/23/2026 08:40 PM |
Dana Chapin |
Installed Resaw Blade |
Band Saw 18 Inch Laguna M1 |
In Service |
|
2,890 |
| 01/23/2026 03:41 PM |
Rick VanHatten |
Entered into system. Not installed yet |
Band Saw Jet 14 Inch M7 |
Out of Service |
|
2,889 |
| 01/22/2026 11:21 AM |
Lynn Welling |
dust gate on drum sander M11 inop for auto open/close. Key at sup desk |
Drum Sander 25 Inch Supermax M11 |
In Service |
Yes |
2,888 |
| 01/21/2026 09:11 PM |
Jerry Mackelburg |
The blast gate’s acrylic slider was removed to essentially keep the gate “open” all the time. But user’s need to still need to ensure that the dust collector is on for dust collection to work. Signage was added to the start/stop switch accordingly. Maybe it can stay there this time until the problem gets corrected? |
Planer 16 Inch Laguna 5HP M45 |
Limited Functionality |
Yes |
2,887 |
| 01/21/2026 09:00 PM |
Jerry Mackelburg |
Doug changed the sandpaper. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,886 |
| 01/20/2026 05:32 PM |
Jerry Mackelburg |
The previously re-wired and connected 208V – 218V 500VA boost transformer (for the 220V 5HP motor) was mounted to the side of the cabinet at 466 hrs and 546 kWhrs of use. |
Planer 20 Inch General International M29 |
In Service |
|
2,885 |
| 01/20/2026 05:20 PM |
Jerry Mackelburg |
Installed 208V – 229V 750VA boost transformer to properly support the 230V 4.5HP motor. |
Band Saw 18 Inch Laguna M1 |
In Service |
|
2,884 |
| 01/19/2026 04:21 PM |
Jeremy Winters |
Lever to rotate miter replaced, kerf plates replaced, fully operational. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,883 |
| 01/18/2026 05:47 PM |
Rick VanHatten |
Not an issue. Disregard previous Entry |
Spindle Sander Powermatic M34 |
In Service |
|
2,882 |
| 01/18/2026 11:25 AM |
Dan McNaughton |
Unable to use need thread adapter |
Spindle Sander Powermatic M34 |
Out of Service |
|
2,881 |
| 01/17/2026 10:16 PM |
Jerry Mackelburg |
The 500 kVA transformer mentioned in Rpt. No. 2871 has been rewired and installed to provide the required ~220V. |
Planer 20 Inch General International M29 |
In Service |
|
2,880 |
| 01/17/2026 09:57 PM |
Jerry Mackelburg |
Regarding Rpt. No. 2876, from Rpt.No. 2870 “Regarding Rpt. No. 2861, the slider has now been removed from the planer’s blast gate (essentially leaving the gate open) until the controller gets fixed. Since the controller won’t be able to turn the dust collector on until it gets repaired, signage has been added to the planer’s power switch to inform users that the dust collector may need to be turned on (if it’s not already on).” Replaced the signage, which had been removed. |
Planer 16 Inch Laguna 5HP M45 |
Limited Functionality |
Yes |
2,879 |
| 01/17/2026 09:47 PM |
Jerry Mackelburg |
The blast gate needs to be operated manually – I.e. the thin black acrylic slider needs to be pulled outward to open the blast gate (to enable dust collection) and pushed inward to close it. The dust collector may also need to be controlled manually (turned on and off) (via the green and red pushbutton switches on its control panel near the rollup door. |
Spindle Sander Enlon M33 |
Limited Functionality |
Yes |
2,878 |
| 01/17/2026 09:46 PM |
Jerry Mackelburg |
The blast gate needs to be operated manually – I.e. the thin black acrylic slider needs to be pulled outward to open the blast gate (to enable dust collection) and pushed inward to close it. The dust collector may also need to be controlled manually (turned on and off) (via the green and red pushbutton switches on its control panel near the rollup door. |
Belt/Disk Sander Jet M6 |
Limited Functionality |
Yes |
2,877 |
| 01/17/2026 12:12 PM |
Dana Chapin |
Dust collector is not starting when machine starts. The gate opens, but the collector doesn’t start |
Planer 16 Inch Laguna 5HP M45 |
In Service |
Yes |
2,876 |
| 01/17/2026 10:21 AM |
Paul Schankin |
Ref 2845. HV power supply replaced. Ran tests, machine in service. |
Laser Thunder Nova 35 M18 |
In Service |
|
2,875 |
| 01/15/2026 11:05 AM |
Paul Schankin |
Changed desiccant, was at 30%, now at 17%. Loaded new filament, ran test job. Machine in service. |
3D Printer |
In Service |
|
2,874 |
| 01/14/2026 08:00 PM |
Jeff Bratt |
Bryan reports the blade installed is a narrow kerf veneer blade. It was difficult to resaw heavier material. Do we have the right size blade of the same type as on the old resaw bandsaw? |
Band Saw 18 Inch Laguna M1 |
In Service |
|
2,873 |
| 01/14/2026 10:58 AM |
Duane Kuperus |
Lou Cortellini and I performed quaterly Lub and Tune on the #1 table saw. |
Table Saw 10 Inch #1 Sawstop Industrial 5HP M35 |
In Service |
|
2,872 |
| 01/13/2026 05:14 PM |
Jerry Mackelburg |
The 750 kVA boost transformer was removed for use on the 16″ planer. One of the 500 kVA transformers will be rewired (from ~24V to ~12V boost) and installed soon to provide the ~220V required by the motor. |
Planer 20 Inch General International M29 |
In Service |
|
2,871 |
| 01/13/2026 05:09 PM |
Jerry Mackelburg |
Regarding Rpt. No. 2861, the slider has now been removed from the planer’s blast gate (essentially leaving the gate open) until the controller gets fixed. Since the controller won’t be able to turn the dust collector on until it gets repaired, signage has been added to the planer’s power switch to inform users that the dust collector may need to be turned on (if it’s not already on).
Regarding Rpt. No. 2862, the progressive tare-out across the end of the workpiece shown in the image seems to suggest the depth of cut was excessive for the grain structure and/or feed direction. IMO it would be quite useful if images and videos could be added/linked to the shop log. Maybe even identifying the member that experienced the problem?
The 750kVA boost transformer was removed from the 20″ planer, re-wired to provide ~24V (rather than ~12V) boost for the 230V motor, installed, and tested at ~2 hrs. and ~3.2kWhr of shop usage. |
Planer 16 Inch Laguna 5HP M45 |
In Service |
|
2,870 |
| 01/13/2026 11:27 AM |
Dana Chapin |
Changed blade |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,869 |
| 01/13/2026 09:01 AM |
Paul Schankin |
Drained approx 1/4 cup water out of tank. In service. |
Air Compressor Fortress |
In Service |
|
2,868 |
| 01/13/2026 09:00 AM |
Paul Schankin |
Replaced dc bag, cleaned filters. Bag at 80%. |
Dust Extractor Bosch |
In Service |
|
2,867 |
| 01/13/2026 08:59 AM |
Paul Schankin |
Replaced dc bag, 75% full. |
Shop Vac Rigid |
In Service |
|
2,866 |
| 01/13/2026 08:03 AM |
Paul Schankin |
Ref 2864. Defective controller, no relay output. Must start dust collector manually. |
Spindle Sander Enlon M33 |
Limited Functionality |
Yes |
2,865 |
| 01/12/2026 08:32 PM |
Nancy Bosecker |
M33 Spindle Sander Blast gate non-operational |
Spindle Sander Enlon M33 |
In Service |
Yes |
2,864 |
| 01/12/2026 07:36 PM |
Nancy Bosecker |
Laguna M3 is sparking and wobbly on startup, before any wood is introduced. Not sure if this is normal, I sent a video to Dana and marked the machine as Limited Service. |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,863 |
| 01/12/2026 07:34 PM |
Nancy Bosecker |
Bad snipe on end of cut in Laguna planer. Sent image to Jerry as to how bad it was. Left machine in service and recommended member us the sander instead. |
Planer 16 Inch Laguna 5HP M45 |
In Service |
|
2,862 |
| 01/12/2026 06:11 PM |
Nancy Bosecker |
Laguna automated dust collection not working. Someone marked the on/off with tape so I’m assuming this is a known issue but entering just in case it’s not known. |
Planer 16 Inch Laguna 5HP M45 |
In Service |
Yes |
2,861 |
| 01/12/2026 06:02 PM |
Jeremy Winters |
Disassembled, cleaned, lubed, reassembled. Miter adjustment much more smooth, no longer grinding. Lever for miter adjust detant hard to engage, new part ordered to replace broken one. Squared and ready for use, still hard to engage miter adjustment until new part replaced. |
Miter Saw 12 Inch Makita M26 |
Limited Functionality |
|
2,860 |
| 01/12/2026 02:16 PM |
Rick VanHatten |
Kirsten Clark…The hose above the right side dust collection barrel outside has one or more holes in it. It’s working, but some dust may escape instead of going into the barrel. It probably needs a new hose, but for now, I will try to find some duct tape to cover it. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,859 |
| 01/12/2026 02:06 PM |
Rick VanHatten |
Kirsten Clark here. planer dust collection hose filled up with shavings and was no longer working. We cleared it, and it seems to be working. But someone should take a closer look. |
Planer 20 Inch General International M29 |
In Service |
Yes |
2,858 |
| 01/10/2026 07:31 PM |
Jerry Mackelburg |
Regarding Rpt.No. 2851, the controller for the blast gate is malfunctioning. The gate blast gate has been left open until it gets fixed. But the dust collector needs to be on for the dust collection to work. A note has been added to the switch accordingly. |
Planer 16 Inch Laguna 5HP M45 |
Limited Functionality |
Yes |
2,857 |
| 01/10/2026 07:20 PM |
Jerry Mackelburg |
Regarding Rpt. No. 2855, the 12AWG power drop had been changed to 8AWG and the current sensor was not rotated to ensure proper operation. Now it has. |
Planer 20 Inch General International M29 |
In Service |
Yes |
2,856 |
| 01/10/2026 01:27 PM |
Duane Kuperus |
When planer starts, the auto blast gate opens then closes with planer still running. Reset controller and no difference |
Planer 20 Inch General International M29 |
Limited Functionality |
|
2,855 |
| 01/10/2026 01:22 PM |
Duane Kuperus |
Sanded with WD40 left table extension and waxed. Rest of table still needs treatment. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,854 |
| 01/10/2026 01:20 PM |
Duane Kuperus |
Realigned Rip Fence |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,853 |
| 01/10/2026 01:19 PM |
Duane Kuperus |
Realigned rip fence |
Table Saw 10 Inch #1 Sawstop Industrial 5HP M35 |
In Service |
|
2,852 |
| 01/10/2026 01:18 PM |
Duane Kuperus |
Blast gate inoperable automatically. Rebooted and shows error code 1 |
Planer 16 Inch Laguna 5HP M45 |
Out of Service |
Yes |
2,851 |
| 01/10/2026 01:17 PM |
Duane Kuperus |
Lubricated elevation threaded rod |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,850 |
| 01/10/2026 01:16 PM |
Duane Kuperus |
Lubricated elevation threaded rod and now it works fine |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,849 |
| 01/09/2026 04:45 PM |
Jerry Mackelburg |
The Wixey DRO needed to be recalibrated. |
Planer 20 Inch General International M29 |
In Service |
|
2,848 |
| 01/09/2026 04:43 PM |
Jerry Mackelburg |
Regarding Rep No. 2843, I couldn’t identify any unexpected noises or deposited metal particles before or while initially planing 1mm off of a 14.25″ wide X 24″ long poplar board. Inspected all 108 carbide cutters and verified that their fasteners were not loose with a torque screwdriver set to 50 in-lb. Thoroughly cleaned the cutter head and its casting as well as the infeed and outfeed rollers.
As a final check after re-assembly, the planer which now has ~1hr of use in our shop, draws about 900 Watts from its 208V supply when not cutting, and 2.8 kW when cleanly removing 1mm form a 14.25 wide poplar board at 16 ft/min.
The outfeed roller is rubber coated so it’s unlikely that it could have caused a metal piece to be pressed into the piece of Sapele to the extent that it was flush with the surface. It seems more likely that metal was already in the wood and cut during planing (which could explain both the “noises” and the metal “speckles”). It’s important to check wood of unknown origin and/or questionable appearance properly with the metal detector before using it on any of the shop’s machines. The carbide cutters on that planer can be broken easily when cutting metal and cost $9 each to replace. |
Planer 16 Inch Laguna 5HP M45 |
In Service |
|
2,847 |
| 01/09/2026 12:48 PM |
Duane Kuperus |
Cleaned and Lubricated Table Saw #2 internal Blade Elevation and Blade Tilt gears/trunion bearings. Also aligned left table extension to level with table saw table. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,846 |
| 01/09/2026 11:27 AM |
Paul Schankin |
Nova 35 out of service. Defective HV power supply. |
Laser Thunder Nova 51 M19 |
Out of Service |
|
2,845 |
| 01/09/2026 11:20 AM |
Patrick Duffy |
Laser power supply failiar. |
Laser Thunder Nova 35 M18 |
Out of Service |
|
2,844 |
| 01/09/2026 09:52 AM |
Oi Ling Kwan |
Laguna Planer making noises and deposits metal speckles on the wood surface |
Planer 16 Inch Laguna 5HP M45 |
Out of Service |
|
2,843 |
| 01/08/2026 09:39 PM |
Rick VanHatten |
Out of Napkins |
Supplies |
Out of Service |
|
2,842 |
| 01/08/2026 06:14 PM |
Nels Lundgren |
Got more 120 sand paper and a gallon of Titebond 3 |
Supplies |
In Service |
|
2,841 |
| 01/07/2026 03:53 PM |
Doug Murphy |
Changed blade on M03 band saw. Looked like someone cut a nail on the old one |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,840 |
| 01/07/2026 01:43 PM |
Michael Ross |
a new chuck key is attached to the drill press with a magnet now |
Drill Press 18 Inch Delta M9 |
In Service |
|
2,839 |
| 01/07/2026 08:49 AM |
Rick VanHatten |
Placed In Service – Replaced LT-16 that is being sold |
Band Saw 18 Inch Laguna M1 |
In Service |
|
2,838 |
| 01/07/2026 08:44 AM |
Rick VanHatten |
Place In Service. Replacement for LT-16 that is being sold |
Band Saw 18 Inch Laguna M1 |
In Service |
|
2,837 |
| 01/06/2026 10:20 PM |
Jerry Mackelburg |
A 208V – 230V voltage boost transformer (rated for a 20.8A maximum load) was inserted in line to satisfy the specified 230V motor input voltage requirement. That should keep the motor happier while maximizing the saw’s cutting power availability. |
Table Saw 10 Inch #1 Sawstop Industrial 5HP M35 |
In Service |
|
2,835 |
| 01/06/2026 10:00 PM |
Jerry Mackelburg |
Thanks to Bryan and Bengt, the power wiring was upgraded to 10 AWG to support the 30A circuit requirement. The table height adjustment worm gear was greased as were the feed roller chains. The table lift chain was lubricated with Dupont “Chain-Saver” wax-based spray lubricant. |
Planer 16 Inch Laguna 5HP M45 |
In Service |
|
2,834 |
| 01/06/2026 09:31 AM |
Paul Schankin |
Ref 2832. Removed broken filament, cleaned and lubed lead screws, cleaned XY rods, ran test print, machine in service. |
3D Printer |
In Service |
|
2,833 |
| 01/05/2026 02:00 PM |
Patrick Duffy |
Broken filament stuck in print head/nozzle |
3D Printer |
Out of Service |
|
2,832 |
| 01/03/2026 09:28 PM |
Jerry Mackelburg |
A member could have benefited from using a rip blade today, but it was appropriately marked as dull and not usable. Maybe the shop needs another one? |
Table Saw 10 Inch #1 Sawstop Industrial 5HP M35 |
Limited Functionality |
|
2,831 |
| 01/03/2026 09:21 PM |
Jerry Mackelburg |
Cleaned rust off the tables and applied Boeshields T-9. Greased table lift leadscrews and oiled their columns. Checked gearbox oil level and installed power/energy meter. Temporarily installed 208V – 230V (<20.8A load) boost transformer from the retired 15A Powermatic for use until a higher power version (<31A load) unit arrives for this 25A planer. |
Planer 16 Inch Laguna 5HP M45 |
In Service |
|
2,830 |
| 01/03/2026 08:53 PM |
Jerry Mackelburg |
Upper right fence is too close to blade at 45 degree (and other angle?) left miters! |
Miter Saw 12 Inch Makita M26 |
Limited Functionality |
|
2,829 |
| 01/03/2026 11:25 AM |
Rick VanHatten |
test |
Supplies |
In Service |
|
2,828 |
| 01/03/2026 10:59 AM |
Nancy Bosecker |
Blast gate on the giant lathe does not open, even when the button is pressed. (reported by Dara at HGS Build) |
Not a Tool Repair Issue |
In Service |
Yes |
2,827 |
| 01/03/2026 10:07 AM |
Tom Bamburg |
Removed mag safe controller and installed factory switch. |
Disk/Belt Sander Jet M38 |
In Service |
|
2,826 |
| 01/02/2026 10:52 AM |
Dana Chapin |
Circuit breaker was in the off position, not the tripped position. Reset the breaker. Started and stopped the machine 10 times. Ran the machine for 10 minutes. Made several cits in 1.5 inch thick oak. No problems observed. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,825 |
| 01/02/2026 09:04 AM |
Mark Umphres |
Will not star |
Band Saw 14 SE Laguna M3 |
Out of Service |
|
2,824 |
| 12/31/2025 04:38 PM |
Rick VanHatten |
Replaced Powermatic 15″ with Laguna 16″ – 5HP. Selling Powermatic that was new April of 2024. Need to upgrade electrical circuit to 30 amp |
Planer 16 Inch Laguna 5HP M45 |
In Service |
|
2,823 |
| 12/31/2025 04:35 PM |
Rick VanHatten |
Replaced #1 Table Saw that was mid shop with SawStop ICS 5HP donated by Grogan Estate. Older 3HP saw is being sold. Moved new 3HP that was by the back door to mid shop position. |
Table Saw 10 Inch #1 Sawstop Industrial 5HP M50 |
In Service |
|
2,822 |
| 12/31/2025 04:17 PM |
Ron Prater |
Adjusted the fence to 90 deg and the 90 deg stop. The stop does not seem to be too reliable, but it is well set now. The entire suspension system for the fence seems poorly designed. |
Jointer 16 Inch Grizzly M12 |
In Service |
|
2,821 |
| 12/30/2025 05:30 PM |
Duane Kuperus |
Bengt and I installed the new 5HP saw in the shop today in the #2 saw position by the rollup door. The #2 saw is now in the #1 position. The #1 saw is now sitting idle in the west room. This was a ton of work and could not have done it without Bengt. The new 5HP saw is set up and the fence alignment is perfect. Tabletop is cleaned and waxed but still need a bit of TLC. Still need to do a little lube and tune but the saw is in service. Note the 5HP saw is a 20amp saw and the circuit is a 20amp circuit needing an upgrade to 30amp. Should be fine for now but if someone is pushing tough/thick or extra hard wood through the saw, it might trip the breaker. So every one should be attentive to what is being cut on that saw till the circuit gets upgraded. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,819 |
| 12/28/2025 10:58 AM |
Patrick Duffy |
Shapeoko XXL is b ack in service. Failed to reinstate “BitSetter” option in Carbice Create Settings. Ran job. TOK (Ref Report 2814) |
CNC Shapeco XXL M5 |
In Service |
|
2,818 |
| 12/27/2025 12:55 PM |
Duane Kuperus |
Check drum height adjustment |
Drum Sander 25 Inch Supermax M11 |
|
|
2,817 |
| 12/27/2025 12:54 PM |
Duane Kuperus |
Check drum height adjustment |
Drum Sander 25 Inch Supermax M10 |
Limited Functionality |
|
2,816 |
| 12/27/2025 12:08 PM |
Duane Kuperus |
The vertical fence is very difficult to set at 90 degrees. Possible the infeed and outfeed tables need alignment for being parallel. |
Jointer 16 Inch Grizzly M12 |
In Service |
|
2,815 |
| 12/27/2025 08:51 AM |
Nancy Bosecker |
John Barry reports that the CNC is failing to engage with the probe mechanism on the right side after changing the tool. It usually navigates to the probe after zeroing to register but the machine is not doing that currently. I’ll put a sign on it as under maintenance. |
CNC Shapeco XXL M5 |
Out of Service |
|
2,814 |
| 12/27/2025 08:09 AM |
Nancy Bosecker |
We’re out of SuperGlue accelerant which is usually found by the CNCs. We could also use some more double-sided tape! |
Supplies |
|
|
2,813 |
| 12/24/2025 11:42 AM |
Rick VanHatten |
Jeremy, I added you to the Power Tool, tool group so you will now see Miter Saw shop log entries. Barry Tuovinen is also in this tool group and he handles hand power tools. Jeremy you handle miter saw issues. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,812 |
| 12/24/2025 11:25 AM |
Rick VanHatten |
Added Tom Bamburg as Sanding Equipment tool Lead for spindle, edge/belt and edge sanders. Chris, you still have the drum sanders. Nels, give me a call when you have time. Tom has been active on Shop Projects and has woodworking background. |
Disk/Belt Sander Jet M38 |
In Service |
|
2,811 |
| 12/23/2025 09:12 AM |
Paul Schankin |
Ref 2789. Power switch replaced on Rigid shop vac. Machine in service. |
Shop Vac Rigid |
In Service |
|
2,810 |
| 12/22/2025 08:26 PM |
Nels Lundgren |
Found the infeed support jig for TS#1. It was in the back of the pile of jigs for TS#2 |
Not a Tool Repair Issue |
In Service |
|
2,809 |
| 12/22/2025 08:15 PM |
Nancy Bosecker |
Tormek Super Grind wheel is uneven and could benefit from a wheel rebalance. I don’t have any experience with that. |
Sharpening System Tormeck |
In Service |
|
2,808 |
| 12/22/2025 04:22 PM |
Bryan Blacksher |
Dust collection will not shut off automatically. Pushed the red button, it shut off, then automatically turned on some seconds later. Put the lever in the off position in order to keep the system off. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,807 |
| 12/22/2025 12:54 PM |
Michael Ross |
I’ll order a new chuck. In the meantime, the chuck on the other drill press will work |
Drill Press 18 Inch Delta M9 |
Limited Functionality |
|
2,806 |
| 12/20/2025 03:59 PM |
Jerry Mackelburg |
Chuck key is missing |
Drill Press 18 Inch Delta M9 |
Limited Functionality |
|
2,804 |
| 12/20/2025 03:47 PM |
Jerry Mackelburg |
Belts for Jet Belt/Disc sander had been misplaced – 3 spares available! |
Supplies |
In Service |
|
2,803 |
| 12/20/2025 02:37 PM |
Jerry Mackelburg |
Need belts for Jet Belt/Belt Sander |
Supplies |
Limited Functionality |
|
2,802 |
| 12/18/2025 09:34 PM |
Nels Lundgren |
One of the magswitch feather boards is not functional, one of the knobs has been rotated more than half a turn and stripped and therefore does not hold. Put on desk |
Not a Tool Repair Issue |
Out of Service |
|
2,800 |
| 12/18/2025 09:23 PM |
Nels Lundgren |
M06 Jet disk/belt sander is missing a threaded knob that holds the left side of belt shroud in place. Both the disc and belt need replacing, especially the disc. |
Belt/Disk Sander Jet M6 |
Limited Functionality |
|
2,799 |
| 12/18/2025 08:19 PM |
Nels Lundgren |
Missing the infeed support jig for TS#1 |
Not a Tool Repair Issue |
Out of Service |
|
2,798 |
| 12/18/2025 08:18 PM |
Nels Lundgren |
Missing one of the 6″ engineering squares that hangs on the hand tool wall |
Not a Tool Repair Issue |
Out of Service |
|
2,797 |
| 12/18/2025 07:07 PM |
Ray Pathman |
1/2″ Chisel on tool board is missing the wood handle. Needs to be replaced (a new one turned?). Taped “do not use until fixed” on the chisel and put back on the tool board. |
Hand Tools |
Out of Service |
|
2,796 |
| 12/18/2025 07:04 PM |
Ray Pathman |
Large stop button not attached properly. Large button is in router table drawer (upper right) until fixed. Regular stop button works fine until fixed. |
Router Table #1 M30 |
In Service |
|
2,795 |
| 12/18/2025 07:22 AM |
Rick VanHatten |
The miter saw blade was found to have seven, yes seven teeth gone in a row. Replaced blade. Will go back and look at video to figure when this happened and who was involved. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,793 |
| 12/17/2025 07:25 PM |
Jeff Bratt |
Building fire alarm triggered about 6:45 – sounded for about 45 sec, then shut off. Have no idea why – nothing we were doing was out of the ordinary. It’s very loud. |
Not a Tool Repair Issue |
|
|
2,792 |
| 12/15/2025 11:12 AM |
Paul Schankin |
Marked decrease in performance of laser. Cleaned, ran tests, laser working at approx 50% of usual. |
Laser Thunder Nova 51 M19 |
Limited Functionality |
|
2,790 |
| 12/15/2025 08:27 AM |
Paul Schankin |
Per 2787, switch broken, out of service. Parts on order. |
Shop Vac Rigid |
Out of Service |
|
2,789 |
| 12/11/2025 09:27 PM |
Nels Lundgren |
M38 Jet disk/belt sander des not power on |
Disk/Belt Sander Jet M38 |
Out of Service |
|
2,788 |
| 12/11/2025 09:26 PM |
Nels Lundgren |
Rigid shopvac on/off switch does not stay in on position, have to hold it down |
Shop Vac Rigid |
Limited Functionality |
|
2,787 |
| 12/11/2025 04:41 PM |
Patrick Duffy |
Ralph Szaras reported an issue with homing the Shapeoko XXL during initialization. Tested the machine, TOK. Ran 3 jobs. Recycled power twice. No problem. Notice that there was quite a bit id wood chips on the Y rails which may hace caused a homing issue. |
CNC Shapeco XXL M5 |
In Service |
|
2,786 |
| 12/09/2025 09:08 AM |
Paul Schankin |
Reg 2784. Reset XXL homing and ran test job. Machine in service. |
CNC Shapeco XXL M5 |
In Service |
|
2,785 |
| 12/08/2025 08:04 PM |
Mike Makowski |
XXL CNC Lost track of home position and will not reset |
CNC Shapeco XXL M5 |
Out of Service |
|
2,784 |
| 12/08/2025 04:21 PM |
Bryan Blacksher |
Found the gates to the outside dust collection unlocked and the lock had the combination still set, i.e. the combination could have been stolen.
Found the moisture tester cabinet unlocked.
I find some of the lathe drawers unlocked almost every shift I work. |
Not a Tool Repair Issue |
|
|
2,783 |
| 12/08/2025 12:43 PM |
Duane Kuperus |
It was reported that the saw would not start. I inspected the saw and found the light indicating a Slow Flashing green and solid red light. This meant the brake needed adjustment. I was told the member and instructor had just changed the blade and the saw would not start. At the time of the event this indicator light was misread as rapid flashing green and solid read. I turned off the saw and adjusted the brake with the gap tool provided. Reenergized the saw and the solid green light indicated all was well. Saw was energized and returned to service. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,782 |
| 12/06/2025 08:10 PM |
Lou Cortellini |
Brake cartridge activation on #2 Table saw. Blade was stopped when it was touched by operator. no injuries. Replaced brake cartridge and placed old cartridge on office desk. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,781 |
| 12/06/2025 08:00 PM |
Jerry Mackelburg |
Automatic blast gate has been repaired. |
Jointer 16 Inch Grizzly M12 |
In Service |
Yes |
2,780 |
| 12/01/2025 04:11 PM |
Admin |
Blast gate on M12 jointer not opening |
Jointer 16 Inch Grizzly M12 |
In Service |
Yes |
2,779 |
| 11/30/2025 02:16 PM |
Nels Lundgren |
Cleaned off pitch on M11 drum sander paper, by taking it off, bending it backwards to loosen the hardened pitch, then used turpentine and a wire brush and screwdriver to remove as much of the pitch as possible. Also cut four more spare rolls of the drum sander paper. Ran wood through both M11 and M10 and tightened up the sander belts. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,777 |
| 11/29/2025 11:17 AM |
Duane Kuperus |
Replaced sanding belt |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,775 |
| 11/29/2025 11:17 AM |
Duane Kuperus |
Replaced sanding belt. |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,774 |
| 11/28/2025 04:22 PM |
Jerry Mackelburg |
Replaced the Wixey DRO batteries and re-calibrated it |
Planer 20 Inch General International M29 |
In Service |
|
2,772 |
| 11/28/2025 02:35 PM |
Dana Chapin |
Changed ceramics in upper guide. Changed blade. Tracking had been changed resulting in blade not being in the correct position. Their is no reason the tracking should be touched. When changing blade the only adjustment that is needed is setting the blade tension. |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,770 |
| 11/26/2025 06:20 PM |
Jeff Bratt |
Power switch – will not stay ON. The squat Ridgid with the orange tank. |
Shop Vac Rigid |
Limited Functionality |
|
2,769 |
| 11/26/2025 06:18 PM |
Jeff Bratt |
I think the blade is kinked. It jumps out of the guides once per revolution |
Band Saw 14 SE Laguna M3 |
Out of Service |
|
2,768 |
| 11/19/2025 05:08 PM |
Jeff Bratt |
Fast Lever – thickness adjust for sanding pieces wider than the drum. This lever has come off the sander. But I was trying to understand how it’s supposed to work. Looking at the other SuperMax, that Fast Lever also will not adjust the thickness. There is a statement in the manual to “tighten the bolts, but not so tight the fast lever doesn’t move”. I suspect the bolts referred to are too tight on both sanders. The Fast Lever for M11 is in the top drawer of the Supervisor station. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,767 |
| 11/19/2025 04:33 PM |
Duane Kuperus |
Lou Cortellini and I performed lube and tune on this saw. Vacuumed out the internal cabinet and surrounding area. Cleaned and lubricated blade elevation and tilt adjustment mechanisms. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,766 |
| 11/18/2025 09:36 AM |
Paul Schankin |
Ref 2761. M30 and M31 router blast gates are operable. Could not duplicate issue. Machine in service. |
Router Table #1 M30 |
In Service |
Yes |
2,764 |
| 11/18/2025 09:31 AM |
Paul Schankin |
Ref 2762. Dust bins are specific, right and left identified. Right bin MUST be oriented correctly, match blue tape on bin side to arrow on blue tape on bin lid as bin is out of round. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,763 |
| 11/15/2025 10:57 AM |
Dan McNaughton |
Dust Collection Drums tops are warped and almost impossible to fit & close |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,762 |
| 11/15/2025 10:36 AM |
Dan McNaughton |
Dust collection gates on M30 & M31 Routers Do not close |
Router Table #1 M30 |
Limited Functionality |
Yes |
2,761 |
| 11/13/2025 05:01 PM |
Jerry Mackelburg |
WRT Rpt. No. 2758, the limiter on the feed rate shaft earlier today was ~3/16″ shorter than the one on the Powermatic planer. That’s apparently short enough to reliably keep the feed rollers from being driven on either planer. Both planers now have 2″ long pieces of 1/2″ SCH 40 rigid PVC limiters on the feed rate shafts to keep them at a 16 FPM feed rate. A (2″ long?) limiter had done its job without incident for almost 4 years on this planer. |
Planer 20 Inch General International M29 |
In Service |
|
2,760 |
| 11/13/2025 04:16 PM |
Jerry Mackelburg |
The blade snapped immediately upon contact with 1/2″ SCH 40 rigid PVC conduit. A new blade was installed, tracked, and tensioned. The blade guides were adjusted to reduce blade friction. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,759 |
| 11/12/2025 06:12 PM |
Jerry Mackelburg |
After entering Rpt. No. 2757, Doug got the planer to feed again by pulling out the feed rate control knob. He said that it was tight but that the limiter on the shaft still allows it to be pushed in enough to put the feed drive in neutral (off). Same problem as reported in Rpt. No. 2764!? |
Planer 20 Inch General International M29 |
In Service |
|
2,758 |
| 11/12/2025 02:11 PM |
Doug Murphy |
Planer not feeding |
Planer 20 Inch General International M29 |
Out of Service |
|
2,757 |
| 11/11/2025 10:54 AM |
Paul Schankin |
Replaced dust collection bag, was at 90% full. Machine in service. |
Sanding Station M05 |
In Service |
|
2,756 |
| 11/10/2025 07:36 PM |
Skip Florey |
There is one blade left for bandsaw M03 |
Not a Tool Repair Issue |
In Service |
|
2,755 |
| 11/10/2025 07:32 PM |
Skip Florey |
Blade on bandsaw M03 snaped and I replaced it There is one M03 blade left |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,749 |
| 11/08/2025 08:59 PM |
Jerry Mackelburg |
Blast gate controller needed to be reset (was reporting “Closing” when closed). |
Router Table #1 M30 |
In Service |
Yes |
2,752 |
| 11/08/2025 08:56 PM |
Jerry Mackelburg |
As reported in Rpt. No. 2743, the wooden fence (which had been damaged) was removed and replaced with the original Makita aluminum upper fence. For safety and performance, it’s important that workpieces contact the fence on both sides of the blade, so that’s likely the best approach for the shop since users weren’t adjusting the wooden fences to enable that for small cutoffs. Unfortunately, the upper fence is somewhat behind the lower fence so it can appear that taller workpieces aren’t against the fence. They also need to be removed for bevel cuts. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,751 |
| 11/04/2025 09:17 AM |
Paul Schankin |
Replaced dust collection bags, both Rigid shop vacs. |
Shop Vac Rigid |
In Service |
|
2,746 |
| 11/04/2025 09:16 AM |
Paul Schankin |
Replaced dust collection bag |
Shop Vac Craftsman |
In Service |
|
2,745 |
| 10/29/2025 08:07 AM |
Jerry Mackelburg |
Someone removed the sacrificial wooden fences and installed the damaged and out-of-plane Makita aluminum upper fences. That negatively impacts utility, performance, and safety – https://groups.google.com/a/sdfwa.org/g/sdfwa-shift-supervisors/c/tqCVBvesesg/m/8QTfEUFRBAAJ. |
Miter Saw 12 Inch Makita M26 |
Limited Functionality |
|
2,743 |
| 10/28/2025 12:58 PM |
Jerry Mackelburg |
Reset Wixey DRO. |
Planer 20 Inch General International M29 |
In Service |
|
2,740 |
| 10/25/2025 02:13 PM |
Mark Umphres |
LASER LINE ON MAKITA MITER SAW NOT WORKING |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,737 |
| 10/24/2025 09:12 AM |
Paul Schankin |
Bambu Handy mobile app reported bed leveling issues. Ran test print, print successful. Handy mobile app not connecting to camera but desktop app sees camera. |
3D Printer |
In Service |
|
2,736 |
| 10/21/2025 09:13 PM |
Rick VanHatten |
Test Message to confirm Carson Whiting is added to Router Tool Lead Table. Carson, please confirm by replying to rvanhatten@gmail.com & Nels. Thanks |
Router Table #1 M30 |
In Service |
|
2,735 |
| 10/21/2025 09:02 PM |
Rick VanHatten |
Ordered 3 Bandsaw Blades for delivery to Dana. ETA 10-28-2025 |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,734 |
| 10/21/2025 01:48 PM |
Nels Lundgren |
Replaced blade on Bandsaw M02. One spare blade remaining. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,733 |
| 10/21/2025 08:30 AM |
Paul Schankin |
3D printer Red filament broken off inside lower AMS enclosure. Cleared broken filament, ran test job, machine back in service. |
3D Printer |
In Service |
|
2,732 |
| 10/20/2025 07:30 PM |
Steve Carter |
Torn Sanding Belt |
Drum Sander 25 Inch Supermax M10 |
Out of Service |
|
2,731 |
| 10/19/2025 01:21 PM |
Nels Lundgren |
Replaced paper on Drum Sander M10 |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,730 |
| 10/18/2025 03:35 PM |
Jerry Mackelburg |
Blast gate controller needed to be reset (it said “Closing” when already closed and wouldn’t open). |
Router Table #1 M30 |
Limited Functionality |
Yes |
2,729 |
| 10/18/2025 03:02 PM |
Mark Umphres |
Titebond II Premium Empty |
Supplies |
|
|
2,727 |
| 10/18/2025 11:02 AM |
Duane Kuperus |
Installed new sandpaper |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,726 |
| 10/14/2025 10:39 AM |
Patrick Duffy |
Test Message. Do not respond. |
CNC Shapeco HDM M4 |
In Service |
|
2,725 |
| 10/13/2025 06:29 PM |
Nels Lundgren |
Missing the 1/8″ brass setup block |
Not a Tool Repair Issue |
Limited Functionality |
|
2,724 |
| 10/12/2025 02:42 PM |
Nels Lundgren |
Makita slider was hard to move and rough. Lubricated slider of the Makita saw using the black graphite spray lube |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,723 |
| 10/11/2025 03:29 PM |
Duane Kuperus |
Installed new measure tape (right side) on #2 saw. Adjusted rip fence for fit, vertical square and square to blade. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,722 |
| 10/10/2025 09:27 PM |
Nels Lundgren |
Regarding report 2719 that the Makita miter saw bevel angle locking pin does not work. The Makita miter saw does not have a detent lock at 0 degrees bevel. The knob on the front of the slider is tightened to lock the saw bevel angle at 0 degrees. The saw is not broken, it is working as designed. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,720 |
| 10/10/2025 11:47 AM |
Tom York |
Miter saw won’t lock on zero (0). Locking pin won’t work correctly |
Miter Saw 12 Inch Makita M26 |
Out of Service |
|
2,719 |
| 10/09/2025 08:01 PM |
Nels Lundgren |
Replaced blade on M03, very dull. Two spare blades remain |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,718 |
| 10/09/2025 01:09 PM |
Phil Silverstone |
Tormek, it’s wobbly |
Supplies |
Limited Functionality |
|
2,717 |
| 10/08/2025 04:13 PM |
Jeff Bratt |
Adjusted belt – machine is back in service |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,716 |
| 10/08/2025 02:39 PM |
Tom York |
Drum Sander M10–Sanding belt pinched and overlapping at right end and needs to be installed. |
Drum Sander 25 Inch Supermax M10 |
Out of Service |
|
2,715 |
| 10/08/2025 09:11 AM |
Nels Lundgren |
Replaced sand paper on drum sander M10 |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,714 |
| 10/08/2025 08:40 AM |
Nels Lundgren |
measuring tape on Table Saw is worn out and unreadable (if working in inches, an still read the metric units). |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
Limited Functionality |
|
2,713 |
| 10/07/2025 12:12 PM |
Rick VanHatten |
outs of ?? |
Supplies |
In Service |
|
2,710 |
| 10/07/2025 10:48 AM |
Jerry Mackelburg |
Need Que Tips (Swabs) |
Supplies |
In Service |
|
2,709 |
| 10/07/2025 09:58 AM |
Paul Schankin |
Ref 2696. Repaired switch failed again, replaced switch, machine in service. |
Shop Vac Rigid |
In Service |
|
2,708 |
| 10/04/2025 01:47 PM |
Duane Kuperus |
Blast gate does not auto open when M11 sander is energized. Blast get on M10 sander opens. Blast gate on M11 is now open manually. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,707 |
| 10/04/2025 01:44 PM |
Duane Kuperus |
replaced sand paper on M11 Drum Sander |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,706 |
| 10/03/2025 02:50 PM |
Jerry Mackelburg |
Tuesday (9/30/2025), Paul fixed the plug wiring and zip ties were added to help support the weight of the power cable to address two of the issues in Rpt. No. 2,675. |
Sanding Station M05 |
Limited Functionality |
|
2,704 |
| 10/03/2025 02:17 PM |
Rick VanHatten |
Issue resolved |
Jointer 16 Inch Grizzly M12 |
In Service |
|
2,703 |
| 10/03/2025 02:16 PM |
Rick VanHatten |
Dumpster issue resolved |
Not a Tool Repair Issue |
In Service |
|
2,702 |
| 10/03/2025 02:14 PM |
Rick VanHatten |
Supplies Test Message – John, give me a call when & I will show you how this works |
Supplies |
In Service |
|
2,701 |
| 10/03/2025 10:57 AM |
Paul Schankin |
Ref 2699. Blast gate operational, could not duplicate issue. Machine in service. |
Band Saw 14-3000 Laguna M2 |
In Service |
Yes |
2,700 |
| 10/02/2025 06:18 PM |
Scott Baldwin |
Blast gate on band saw M02 not working |
Band Saw 14-3000 Laguna M2 |
Out of Service |
Yes |
2,699 |
| 09/30/2025 04:19 PM |
Jerry Mackelburg |
Problems reported in Rpt. No. 2695 were corrected by cleaning the lift leadscrew and its guides as well as the table under the lift plate. Problem may have been caused/exasperated by the blast gate not operating reliably. (It needed to be reset Saturday afternoon.) |
Router Table #1 M30 |
In Service |
Yes |
2,698 |
| 09/30/2025 11:57 AM |
Paul Schankin |
Ref 2687. Sanding drum removed with spindle. Machine in service. |
Spindle Sander Powermatic M34 |
In Service |
|
2,697 |
| 09/30/2025 11:55 AM |
Paul Schankin |
Ref 2686. AC switch repaired, machine in service. |
Shop Vac Rigid |
In Service |
|
2,696 |
| 09/27/2025 08:03 PM |
Jerry Mackelburg |
The router lift requires excessive force to raise the last inch or so. The right side of the lift plate is above the tabletop. |
Router Table #1 M30 |
Limited Functionality |
|
2,695 |
| 09/27/2025 07:56 PM |
Jerry Mackelburg |
Need strap wrenches |
Supplies |
Limited Functionality |
|
2,694 |
| 09/26/2025 08:41 AM |
Paul Schankin |
AC switch cycled for dust collector control. Takes approx 5 minutes for system to reboot and be operational. Dust collection in service. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,693 |
| 09/26/2025 08:38 AM |
Paul Schankin |
Ref 2689. Acrylic gate replaced, machine in service. |
Band Saw 14-3000 Laguna M2 |
In Service |
Yes |
2,692 |
| 09/25/2025 07:08 PM |
Scott Baldwin |
vacuum air not functioning correctly. Can only work on manual. Blast gates don’t open. |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
Yes |
2,691 |
| 09/25/2025 01:37 PM |
Tom Roetker |
Please add Ray Pathmann as a Shift Supervisor to the Shop Log application |
Not a Tool Repair Issue |
|
|
2,690 |
| 09/25/2025 01:36 PM |
Tom Roetker |
Blast Gate not working, Acrylic plate was jammed, and is now broken in half |
Band Saw 14-3000 Laguna M2 |
Out of Service |
Yes |
2,689 |
| 09/24/2025 02:08 PM |
Tom York |
The dust collection/blast gate for the belt sander is note functioning. |
Edge Sander Jet M15 |
In Service |
Yes |
2,688 |
| 09/24/2025 01:53 PM |
Tom York |
M34 spindle sander is out of order….sandpaper has slipped down the spindle. |
Spindle Sander Powermatic M34 |
Limited Functionality |
|
2,687 |
| 09/23/2025 11:33 AM |
Lou Cortellini |
Rigid shop vac (currently positioned near CNC machine) on off switch is loose. Vac does not want to shut off. |
Shop Vac Rigid |
Limited Functionality |
|
2,686 |
| 09/21/2025 01:02 PM |
Paul Schankin |
Ref # 2683: Nova 35 is operational, cleared file listing and performed maintenance. Machine is service. |
Laser Thunder Nova 35 M18 |
In Service |
|
2,685 |
| 09/21/2025 01:00 PM |
Paul Schankin |
Ref #2682: Auto start and stop of Oneida is operational. Could not duplicate issue. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
Yes |
2,684 |
| 09/20/2025 05:50 PM |
Jerry Mackelburg |
The laser wouldn’t accept a new “Origin” (for me, Marcus, Dallas, or David Collins) until David had it run a small job. |
Laser Thunder Nova 35 M18 |
In Service |
|
2,683 |
| 09/20/2025 12:42 PM |
Duane Kuperus |
Installed new blast gate assembly on M2 Bandsaw. Right after that the dust collection system would not operate in Auto. Operating in manual now. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
Yes |
2,682 |
| 09/20/2025 12:40 PM |
Duane Kuperus |
Installed new blast gate motor assembly. |
Band Saw 14-3000 Laguna M2 |
In Service |
Yes |
2,681 |
| 09/19/2025 10:19 AM |
Paul Schankin |
Vacuumed flapper screen at top of Oneida exhaust due to clogging and excessive back pressure. Dust collection in service. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,680 |
| 09/19/2025 09:40 AM |
Paul Schankin |
Replaced desiccant in AMS enclosure, washed textured plate, ran test print, machine in service. |
3D Printer |
In Service |
|
2,679 |
| 09/18/2025 07:25 PM |
Nels Lundgren |
Repaired M31 router lift, replaced stripped out brass nuts. |
Router Table #2 Rockler M31 |
In Service |
|
2,678 |
| 09/18/2025 06:07 PM |
Nels Lundgren |
Replenished 400 grit sheet sandpaper, 20 sheets |
Supplies |
In Service |
|
2,677 |
| 09/15/2025 05:44 PM |
Nels Lundgren |
Replenished 120 grit sheet sandpaper, 40 sheets |
Supplies |
In Service |
|
2,676 |
| 09/14/2025 01:10 PM |
Jerry Mackelburg |
Yesterday afternoon power was temporarily unavailable at the sanding station because its power plug had partially disengaged from the wall mounted receptacle. That quite heavy cable’s plug should probably be mechanically attached to the receptacle to prevent recurrence. The plug wiring should also be adjusted so the strain relief engages the cable jacket rather than its wires. The Dust Deputy lid doesn’t seem to seal properly to the bucket. The member that experienced the power problem was sanding the (polyurethane?) finish off his workpiece – isn’t that prohibited? |
Sanding Station M05 |
Limited Functionality |
|
2,675 |
| 09/13/2025 10:03 PM |
Jerry Mackelburg |
The dumpster was full at 5PM today (Saturday). |
Not a Tool Repair Issue |
Out of Service |
|
2,674 |
| 09/13/2025 09:56 PM |
Jerry Mackelburg |
One of the more senior and consistent Shop 4.0 upgrade volunteers asked about the location of the router table coping sled that used to be available in the shop. We couldn’t find it. Maybe we should get one? |
Router Table #1 M30 |
Limited Functionality |
|
2,673 |
| 09/13/2025 09:37 PM |
Jerry Mackelburg |
One of the bearings in the router that was reported to have failed in Rpt. No. 2653 had failed. Since OEM upper bearings are no longer available for those routers, a supposedly equivalent PGN bearing was installed during the previous repair ~18 months ago. Another, reportedly higher quality NSK bearing is now installed, as are OEM brushes to replace the off-brand Chinese brushes installed previously. A spare NSK upper bearing and set of OEM brushes were placed in a box with the repaired router and placed in the bottom of the M30 router table cabinet. |
Router Table #2 Rockler M31 |
In Service |
|
2,672 |
| 09/13/2025 05:36 PM |
Nels Lundgren |
Replenished R44 batteries which most of the calipers take. Replaced batteries in all calipers and we are in better shape with working calipers now |
Supplies |
In Service |
|
2,670 |
| 09/13/2025 05:34 PM |
Nels Lundgren |
replenished 220 grit sandpaper 40 sheets and 320 grit sandpaper 20 sheets |
Supplies |
In Service |
|
2,669 |
| 09/12/2025 08:36 AM |
Paul Schankin |
Hot end clogged, cleared clog, ran test print, machine in service. |
3D Printer |
In Service |
|
2,667 |
| 09/11/2025 08:30 PM |
Nels Lundgren |
MiterSet setup tool for miter gauge is missing. It is supposed to be in TS#2 cabinet drawer 2B. I’ve looked in many places and can not find it. I would really like to use it. It is in a plastic box that is about 8″ square and 2″ high. If anyone knows the setup tool I am talking about and knows where it is please et me know. |
Not a Tool Repair Issue |
Out of Service |
|
2,666 |
| 09/11/2025 07:55 PM |
Nels Lundgren |
Missing 3/8″ brass setup block on tool wall |
Not a Tool Repair Issue |
In Service |
|
2,665 |
| 09/10/2025 07:08 PM |
Nels Lundgren |
Reattached the front to back adjustment wheel that had come off. It is attached with a set screw |
Mortiser Powermatic M27 |
In Service |
|
2,664 |
| 09/10/2025 07:06 PM |
Nels Lundgren |
Replaced sand paper on Drum Sander M10 |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,663 |
| 09/09/2025 06:32 PM |
Dana Chapin |
router lift not working |
Router Table #2 Rockler M31 |
Out of Service |
|
2,662 |
| 09/05/2025 12:13 PM |
Rick VanHatten |
test |
Supplies |
In Service |
|
2,660 |
| 09/04/2025 08:36 PM |
Nels Lundgren |
Replaced router motor on table M31 with spare. Old motor does not turn freely, need to perform exploratory surgery. Put it in the bottom cabinet of M30. |
Router Table #2 Rockler M31 |
In Service |
|
2,659 |
| 09/04/2025 08:33 PM |
Nels Lundgren |
Replaced sand paper roll on drum sander M10 |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,658 |
| 09/03/2025 03:25 PM |
Doug Murphy |
need 303 batteries for calipers |
Not a Tool Repair Issue |
In Service |
|
2,656 |
| 09/02/2025 09:31 AM |
Paul Schankin |
Dust collection bag replaced. Last replaced 6/3/2025. |
Shop Vac Craftsman |
In Service |
|
2,655 |
| 09/01/2025 05:58 PM |
Jerry Mackelburg |
Regarding Rpt No. 2653: It’s possible that debris in the router is causing the reported problem. If so, removing the router and lift from the table, turning it upside down, blowing compressed air downward thru it, and running it upside down might clear it to restore normal operation. Folks “cleaning up” by inadvertently blowing debris into the router may have caused the problem. |
Router Table #2 Rockler M31 |
Out of Service |
|
2,654 |
| 09/01/2025 03:55 PM |
Bryan Blacksher |
Router M31makes a very strange noise when started. Stopped and unplugged. When you turn the shaft/collet by hand, every little bit the shaft locks up, either forward or reverse.
I am guessing the motor or bearings. |
Router Table #2 Rockler M31 |
Out of Service |
|
2,653 |
| 08/31/2025 09:21 AM |
Jerry Mackelburg |
It took 3 passes to fully cut 48″ X 24″ X 1/8″ paper masked extruded black acrylic at the recommended settings for acrylic (remnants in the office). Optics need cleaning, laser aged/degraded, recommended settings wrong/not applicable, bed not level, or? |
Laser Thunder Nova 51 M19 |
Limited Functionality |
|
2,651 |
| 08/31/2025 08:43 AM |
Jerry Mackelburg |
A member was unable to “Send” his file to the laser until one of the 99 files was deleted from its controller. I suggested that operating the laser directly from the laser might have avoided that problem (would it?) Maybe the other laser’s controller memory is also full? |
Laser Thunder Nova 35 M18 |
Limited Functionality |
|
2,650 |
| 08/30/2025 11:36 AM |
Dana Chapin |
Dust collection gate not opening or starting duct collector |
Edge Sander Jet M15 |
Limited Functionality |
Yes |
2,649 |
| 08/28/2025 08:23 PM |
Nels Lundgren |
Tuned up the TS#1 Multifunction sled. Tightened the miter bar so that there is no play, and replaced the stop that got all cut up and busted !!?! Geez. Glad I made extra. It is actually pretty accurate with the measuring tape on the fence. As reported by Lou the base of the sled is about 0.4 degrees out from the table top because it is not completely flat. I plan to remake it from more stable material (hopefully) with a few improvements. |
Not a Tool Repair Issue |
In Service |
|
2,648 |
| 08/28/2025 12:53 PM |
Edee Armand |
blade kinked and changed |
Not a Tool Repair Issue |
In Service |
|
2,647 |
| 08/27/2025 06:01 PM |
Jeff Bratt |
PowerMatic drill press – one of the depth stops has lost its spring, so it doesn’t lock into place. I’m pretty sure a replacement could be found at Marshalls if you know what size it should be. |
Drill Press 14 Inch Powermatic M8 |
In Service |
|
2,646 |
| 08/25/2025 06:57 PM |
Nels Lundgren |
Restocked Rosin Paper with four new rolls. In the closet next to the office. |
Supplies |
In Service |
|
2,645 |
| 08/25/2025 04:30 PM |
Rick VanHatten |
Test Message – Air Compressor |
Air Compressor Fortress |
In Service |
|
2,644 |
| 08/25/2025 04:28 PM |
Rick VanHatten |
Test Message – Bandsaw M2 |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,642 |
| 08/25/2025 04:26 PM |
Rick VanHatten |
Test Message – Domino 700 |
Domino DF 700 Festool |
In Service |
|
2,641 |
| 08/25/2025 04:25 PM |
Rick VanHatten |
Test Message – Dust Collector M14 |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,640 |
| 08/25/2025 04:10 PM |
Rick VanHatten |
Test Message – Dust Collector M14 |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,639 |
| 08/25/2025 04:09 PM |
Rick VanHatten |
Test Message – Drill Press M11 |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,638 |
| 08/25/2025 04:09 PM |
Rick VanHatten |
Test Message – Drum Sander M10 |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,637 |
| 08/25/2025 04:07 PM |
Rick VanHatten |
Test Message Drill Press Delta M9 |
Drill Press 18 Inch Delta M9 |
In Service |
|
2,636 |
| 08/25/2025 04:06 PM |
Rick VanHatten |
Test Message Drill Press Powermatic 14 |
Drill Press 14 Inch Powermatic M8 |
In Service |
|
2,635 |
| 08/25/2025 04:05 PM |
Rick VanHatten |
Test Message Domino 500 |
Domino DF 500 Festool |
In Service |
|
2,634 |
| 08/25/2025 04:05 PM |
Rick VanHatten |
test message M38 |
Disk/Belt Sander Jet M38 |
In Service |
|
2,633 |
| 08/25/2025 04:04 PM |
Rick VanHatten |
Test Message |
Belt/Disk Sander Jet M6 |
In Service |
|
2,632 |
| 08/25/2025 03:55 PM |
Rick VanHatten |
Test Message |
CNC Shapeco XXL M5 |
In Service |
|
2,631 |
| 08/25/2025 03:48 PM |
Rick VanHatten |
Test |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,629 |
| 08/25/2025 03:47 PM |
Rick VanHatten |
Test |
Air Compressor Fortress |
In Service |
|
2,628 |
| 08/25/2025 03:39 PM |
Rick VanHatten |
Test Message |
CNC Shapeco HDM M4 |
In Service |
|
2,627 |
| 08/25/2025 03:38 PM |
Rick VanHatten |
Test Message |
Biscuit Jointer |
In Service |
|
2,626 |
| 08/25/2025 03:36 PM |
Rick VanHatten |
Test Message |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,624 |
| 08/25/2025 03:36 PM |
Rick VanHatten |
Test Message |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,623 |
| 08/25/2025 03:35 PM |
Rick VanHatten |
Test Message |
Air Compressor Fortress |
In Service |
|
2,622 |
| 08/25/2025 03:34 PM |
Rick VanHatten |
Test Message |
3D Printer |
In Service |
|
2,621 |
| 08/24/2025 12:58 PM |
Nancy Bosecker |
Please order more of the large paper rolls to protect benches during glue-ups, I used the last piece today. |
Supplies |
|
|
2,620 |
| 08/24/2025 08:31 AM |
Paul Schankin |
Spindle sander, M34, BG not closing completely, throwing error code 1. |
Spindle Sander Powermatic M34 |
Limited Functionality |
Yes |
2,619 |
| 08/23/2025 07:31 PM |
Admin |
Test Shop Log Email |
Not a Tool Repair Issue |
In Service |
|
2,618 |
| 08/23/2025 07:15 PM |
Admin |
test sheet link |
Not a Tool Repair Issue |
In Service |
|
2,617 |
| 08/23/2025 01:45 PM |
Duane Kuperus |
Installed new sand paper on M11 Drum Sander |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,616 |
| 08/22/2025 09:16 PM |
Jerry Mackelburg |
Dumpster is almost full |
Not a Tool Repair Issue |
Limited Functionality |
|
2,615 |
| 08/22/2025 09:15 PM |
Jerry Mackelburg |
Toilet leaks in upstairs bathroom. |
Not a Tool Repair Issue |
Out of Service |
|
2,614 |
| 08/21/2025 01:38 PM |
Admin |
(M10) Drum Sander paper broke. No replacement roll found in bench room, drawer 14B |
Drum Sander 25 Inch Supermax M10 |
Out of Service |
|
2,613 |
| 08/20/2025 08:40 PM |
Mike Davis |
drum sander belt broke |
Drum Sander 25 Inch Supermax M10 |
Out of Service |
|
2,612 |
| 08/20/2025 05:00 PM |
Nels Lundgren |
Repaired the Router Lift on Router Table #1 (M30) |
Router Table #1 M30 |
In Service |
|
2,611 |
| 08/19/2025 11:31 AM |
Paul Schankin |
Grizzly 20″ jointer blast gate has questionable reed relay causing dust collection to run continuously. Replaced blast gate, machine in service. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
Yes |
2,609 |
| 08/18/2025 06:47 PM |
Mike Makowski |
Replace sand belt on drum sander M10 |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,608 |
| 08/18/2025 01:44 PM |
Patrick Duffy |
HDM PC has been replaced. System tested OK. |
CNC Shapeco HDM M4 |
In Service |
|
2,607 |
| 08/16/2025 10:23 PM |
Rick VanHatten |
Repaired tool returned from Festool. Replaced seal on cutter |
Domino DF 700 Festool |
In Service |
|
2,606 |
| 08/16/2025 08:39 PM |
Jerry Mackelburg |
Need Teflon tape. |
Supplies |
Limited Functionality |
|
2,605 |
| 08/16/2025 08:38 PM |
Jerry Mackelburg |
Dumpster is almost full. |
Not a Tool Repair Issue |
Limited Functionality |
|
2,604 |
| 08/16/2025 08:36 PM |
Jerry Mackelburg |
Replaced broken slider in blast gate to restore operation. Might have used last spare 5″ slider. |
Router Table #2 Rockler M31 |
In Service |
Yes |
2,603 |
| 08/16/2025 10:59 AM |
Dan McNaughton |
No glue brushes available those in the shop were unusable caked with glue not previously washed. |
Not a Tool Repair Issue |
|
|
2,602 |
| 08/16/2025 10:28 AM |
Dan McNaughton |
Opened shop at 8am, Sat 9/16/2025, alarm system not set the previous night. |
Not a Tool Repair Issue |
|
|
2,600 |
| 08/16/2025 10:24 AM |
Dan McNaughton |
Compressor needs maintaiance, excess water i tannc |
Air Compressor Fortress |
Limited Functionality |
|
2,599 |
| 08/15/2025 09:17 PM |
Jerry Mackelburg |
Shortened hose to eliminate the leaks reported in Rpt No. 2591 |
Air Compressor Fortress |
In Service |
|
2,598 |
| 08/15/2025 05:37 PM |
Rick VanHatten |
Returned from Festool. |
Domino DF 700 Festool |
In Service |
|
2,597 |
| 08/15/2025 11:14 AM |
Paul Schankin |
Dust collection bag at 80% full. Replaced DC bag. Machine in service. |
Shop Vac Rigid |
In Service |
|
2,596 |
| 08/15/2025 08:33 AM |
Tom York |
One 125 inch bandsaw blade left in the drawer. More blades needed?? |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,595 |
| 08/14/2025 01:40 PM |
Lou Cortellini |
Out of 150 grit sandpaper |
Supplies |
In Service |
|
2,594 |
| 08/14/2025 01:07 PM |
Lou Cortellini |
Blast gate is disconnected. When connected, it turns on dust collection (even when sander is off). |
Edge Sander Jet M15 |
In Service |
Yes |
2,593 |
| 08/13/2025 03:05 PM |
Tom York |
The bandsaw blade on M02 has been replace. Machine now working. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,592 |
| 08/13/2025 02:40 PM |
Tom York |
Bandsaw M)2 blade is broken… |
Band Saw 14-3000 Laguna M2 |
Out of Service |
|
2,591 |
| 08/13/2025 12:26 PM |
Rick VanHatten |
Repaired Domino 700 returned from Festool |
Domino DF 700 Festool |
In Service |
|
2,590 |
| 08/13/2025 09:38 AM |
Rick VanHatten |
Festool repaired and back in service. Replaced sealing ring (700027), spindle housing (73503), needle bearing (720769) |
Domino DF 700 Festool |
In Service |
|
2,589 |
| 08/13/2025 09:35 AM |
Rick VanHatten |
Restocked AAA batteries |
Supplies |
In Service |
|
2,588 |
| 08/12/2025 09:34 PM |
Jerry Mackelburg |
It’s only Tuesday night and the dumpster is at least half full! Lots of milling today! |
Not a Tool Repair Issue |
In Service |
|
2,587 |
| 08/12/2025 09:28 PM |
Jerry Mackelburg |
The drums overfilled today during a heavy milling session – the amber indicator light was flashing at the time. But, the static pressure which is typically over 13.5″ WG with all the blast gates closed, had dropped to the 4.4″ WG and the screen at the top of the exhaust tube was almost fully clogged. A shop VAC with a long extension wand was used to vacuum off the screen and restore normal operation. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,586 |
| 08/12/2025 09:09 PM |
Jerry Mackelburg |
The blast gate occasionally opens and turns the Oneida on while the jointer is off (it happened twice today). It stays open with the Oneida on until the jointer power is cycled on to off. There is no indication on the supervisor station static pressure display when the jointer is on. (That jointer experienced lots of use today). |
Jointer 16 Inch Grizzly M12 |
Limited Functionality |
Yes |
2,585 |
| 08/12/2025 08:51 PM |
Jerry Mackelburg |
Multiple leaks near the far end of the hose causes the compressor to run almost continuously when turned on. |
Air Compressor Fortress |
Limited Functionality |
|
2,584 |
| 08/12/2025 08:46 PM |
Jerry Mackelburg |
Alignment arrows on blue tape were placed on the right lid and drum to make lid installation easier. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,583 |
| 08/11/2025 08:18 PM |
Nancy Bosecker |
Replaced sandpaper on M11 Drum Sander as a member violated the 1/8″ turn rule and the paper ripped. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,582 |
| 08/11/2025 02:25 PM |
Rick VanHatten |
Need: 1. Dominos -5×30 2. Titebond III |
Supplies |
|
|
2,581 |
| 08/10/2025 03:20 PM |
Patrick Duffy |
HDM PC power supply failure. |
CNC Shapeco HDM M4 |
Out of Service |
|
2,580 |
| 08/09/2025 02:49 PM |
Jerry Mackelburg |
Need AAA Alkaline batteries |
Supplies |
Limited Functionality |
|
2,578 |
| 08/09/2025 11:02 AM |
Duane Kuperus |
installed new 80 grit sandpaper |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,577 |
| 08/09/2025 10:40 AM |
Dan McNaughton |
Top on dust collection barrel is warped and difficult to close |
Not a Tool Repair Issue |
In Service |
|
2,576 |
| 08/07/2025 11:12 AM |
Duane Kuperus |
Lou Cortellini and I lubricated and greased the saw blade elevation and tilt mechanisms on 8/4/25 |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,575 |
| 08/07/2025 11:10 AM |
Duane Kuperus |
Adjusted out-feed table legs on @2 tsble saw. The out-feed table no longer interferes with wood being cut. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,573 |
| 08/06/2025 06:51 PM |
Ron Prater |
Outfeed table is higher than the saw table. Wood being ripped hangs up on the joint with the outfeed table. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,572 |
| 08/06/2025 03:56 PM |
Doug Murphy |
Router table M30 height adjustment out |
Router Table #1 M30 |
Out of Service |
|
2,571 |
| 08/06/2025 01:28 PM |
Doug Murphy |
almost out of large nitrile gloves |
Supplies |
Limited Functionality |
|
2,570 |
| 08/05/2025 05:21 PM |
Jerry Mackelburg |
Finished adjusting the new carbide cutters. |
Planer 20 Inch General International M29 |
In Service |
|
2,568 |
| 08/04/2025 03:38 PM |
Bryan Blacksher |
Could not dump the inside trash that I gathered up, nor empty the barrels (even though the light was flashing amber), because the dumpster was chock full. |
Not a Tool Repair Issue |
|
|
2,567 |
| 08/03/2025 04:57 PM |
Jerry Mackelburg |
Recent damage to the right drum is making it difficult to attach the cover. Rotating the drum to a “sweet spot” can enable the installation and use of the cover clamping band to do it. |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
2,566 |
| 07/31/2025 05:20 PM |
Rick VanHatten |
Cleaning up Shop Log |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,565 |
| 07/31/2025 03:27 PM |
Rick VanHatten |
Spindle seal failed. Sent to Festool for repair on 7-30-2025 |
Domino DF 700 Festool |
Out of Service |
|
2,563 |
| 07/30/2025 04:16 PM |
Jerry Mackelburg |
54 (of 58) new carbide cutter inserts were installed on Saturday. After playing whack a mole for several days attempting to get them properly adjusted, they’re finally at a point where they should be adequate for most users. I’ll work on further improvements when feasible/convenient. |
Planer 20 Inch General International M29 |
In Service |
|
2,562 |
| 07/28/2025 12:15 PM |
Ron Prater |
Placing back in service. |
Jointer 12 Inch Grizzly M16 |
In Service |
|
2,561 |
| 07/28/2025 11:14 AM |
Jerry Mackelburg |
Adjusting New Cutters |
Planer 20 Inch General International M29 |
Limited Functionality |
|
2,560 |
| 07/28/2025 08:08 AM |
Rick VanHatten |
Jerry this is a test. Please place machine back in service. Rick |
Jointer 12 Inch Grizzly M16 |
Out of Service |
|
2,559 |
| 07/28/2025 08:04 AM |
Rick VanHatten |
Test 7-28-2025 |
Supplies |
In Service |
|
2,556 |
| 07/27/2025 08:31 PM |
Admin |
Testing (disregard) |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,553 |
| 07/27/2025 08:28 PM |
Admin |
testing |
Not a Tool Repair Issue |
|
|
2,552 |
| 07/27/2025 06:49 PM |
Duane Kuperus |
Table Saw 10 Inch #1 Sawstop Industrial (M35) |
Test Tool |
|
|
2,551 |
| 07/27/2025 06:48 PM |
Rick VanHatten |
Band Saw 14 SE Laguna (M3) |
Test Tool |
In Service |
|
2,550 |
| 07/27/2025 06:45 PM |
Rick VanHatten |
Supplies |
Test Tool |
In Service |
|
2,549 |
| 07/27/2025 06:34 PM |
Admin |
Not a Tool Repair Issue |
Test Tool |
|
|
2,548 |
| 07/27/2025 06:31 PM |
Admin |
Not a Tool Repair Issue |
Test Tool |
|
|
2,547 |
| 07/27/2025 06:28 PM |
Admin |
Not a Tool Repair Issue |
Test Tool |
|
|
2,546 |
| 07/27/2025 06:26 PM |
Admin |
Not a Tool Repair Issue |
Test Tool |
|
|
2,545 |
| 07/27/2025 06:15 PM |
Admin |
Not a Tool Repair Issue |
Test Tool |
|
|
2,544 |
| 07/27/2025 06:08 PM |
Admin |
Not a Tool Repair Issue |
Test Tool |
|
|
2,543 |
| 07/24/2025 07:51 PM |
Scott Baldwin |
|
|
|
|
2,542 |
| 07/24/2025 07:39 PM |
Scott Baldwin |
|
|
|
|
2,541 |
| 07/15/2025 06:32 PM |
Dana Chapin |
|
|
|
|
2,540 |
| 07/10/2025 10:32 AM |
Lynn Welling |
|
|
|
|
2,539 |
| 07/09/2025 03:35 PM |
Doug Murphy |
|
|
|
|
2,538 |
| 07/09/2025 03:34 PM |
Doug Murphy |
|
|
|
|
2,537 |
| 07/09/2025 03:34 PM |
Doug Murphy |
|
|
|
|
2,536 |
| 07/09/2025 03:32 PM |
Patrick Duffy |
|
|
|
|
2,535 |
| 07/05/2025 05:15 PM |
Dana Chapin |
|
|
|
|
2,534 |
| 07/05/2025 12:50 PM |
Dana Chapin |
|
|
|
|
2,533 |
| 07/05/2025 12:50 PM |
Dana Chapin |
|
|
|
|
2,532 |
| 07/01/2025 09:07 PM |
Jerry Mackelburg |
|
|
|
|
2,531 |
| 07/01/2025 09:06 PM |
Jerry Mackelburg |
|
|
|
|
2,530 |
| 06/25/2025 01:00 PM |
Patrick Duffy |
|
|
|
|
2,529 |
| 06/22/2025 04:59 PM |
Jerry Mackelburg |
|
|
|
|
2,528 |
| 06/21/2025 09:12 PM |
Jerry Mackelburg |
|
|
|
|
2,527 |
| 06/21/2025 02:25 PM |
Mark Umphres |
|
|
|
|
2,526 |
| 06/18/2025 09:12 PM |
Dallas Keck |
|
|
|
|
2,525 |
| 06/18/2025 08:02 PM |
Rick VanHatten |
|
|
|
|
2,524 |
| 06/10/2025 07:51 AM |
Paul Schankin |
Blast gate not reporting in HA but is operational. Rebooted controller, still not reporting. |
Band Saw 14 SE Laguna M3 |
In Service |
Yes |
2,522 |
| 06/10/2025 07:50 AM |
Tom Roetker |
Sled needs to have the rail |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
Limited Functionality |
|
2,521 |
| 06/09/2025 03:32 PM |
Tom Roetker |
Please add Kirsten Clark to list of Shop Supervisors in the Shop Log entry screen. |
Not a Tool Repair Issue |
In Service |
|
2,520 |
| 06/09/2025 03:30 PM |
Tom Roetker |
Please add Ray Pathmann to the list of Shop Supervisors in the Shop Log entry screen. Thanks! |
Not a Tool Repair Issue |
In Service |
|
2,519 |
| 06/07/2025 07:41 PM |
Tom Roetker |
Bryan Harding reporting: Broke blade replace. Note blades are in boxes that do not match the correct blade length on the box or the paper indicating that the M02 bandsaw uses 111in blades might be wrong. Not sure but it took few tries to find the right length blade. Tension meter worked great! |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,517 |
| 06/07/2025 09:30 AM |
Bryan Blacksher |
Tripping the circuit breaker likely the makesafe device |
Disk/Belt Sander Jet M38 |
Out of Service |
|
2,516 |
| 06/06/2025 07:50 PM |
Tom Roetker |
Green run light appears to be burned out. Makes a dangerous situation in that there is no obvious indication that the jointer is running. This was submitted by Bryan Harding during intro class |
Jointer 12 Inch Grizzly M16 |
In Service |
|
2,515 |
| 06/04/2025 09:35 PM |
Jerry Mackelburg |
Paul S. and I cleared the blockage in the exhaust output port that was severely impacting recent performance. Someone allowed the dust collection drums to overflow and cause the blockage. More effort is clearly required to prevent recurrence (which negatively impacts equipment performance and personnel health.) |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,514 |
| 06/04/2025 07:29 PM |
Nancy Bosecker |
Router Table #1 fence has a divot cut out on the left hand side of the table. It is significant enough to make pushing through against the fence problematic. Should be repaired or replaced. |
Not a Tool Repair Issue |
In Service |
|
2,513 |
| 06/03/2025 01:00 PM |
Paul Schankin |
Updated 3D printer laptop, Bambu to V2.1.0.59. Ran test print, machine in service |
3D Printer |
In Service |
|
2,512 |
| 06/03/2025 12:58 PM |
Paul Schankin |
Replaced dust collection bag, 80% full. In service. |
Shop Vac Craftsman |
In Service |
|
2,511 |
| 06/03/2025 12:32 PM |
Paul Schankin |
Drained approx 1/4 cup of water from tank. Machine in service. |
Air Compressor Fortress |
In Service |
|
2,510 |
| 06/03/2025 10:17 AM |
Paul Schankin |
Verified AMS working all 4 slots, loaded red PLA slot 2, ran test print, machine in service. |
3D Printer |
In Service |
|
2,508 |
| 06/01/2025 10:24 AM |
Rick VanHatten |
Test confirming addition of Cole Roberts to the distribution for 3D printer issues |
3D Printer |
In Service |
|
2,506 |
| 05/30/2025 09:26 AM |
Michael Ross |
Scott Thomson had moved the spindle mount to increase the distance between pulleys to tighten the belts last Tuesday. I tried to move them a little farther. I then drilled a 2″ hole into the densest wood I could find and the belts didn’t slip. This should be adequate belt tension. |
Drill Press 18 Inch Delta M9 |
In Service |
|
2,505 |
| 05/28/2025 06:16 PM |
Ron Prater |
Adjusted outfeed table slightly higher, couldn’t see any snipe against a straight edge. Adjusted the fence and stop for 90 deg. Cleaned out all the interior dust conduits, but no blockage was visible. It still produces more chips on the floor than desirable, but everything is working. The gate valve doesn’t operate, so it’s fixed open now. |
Jointer 16 Inch Grizzly M12 |
In Service |
|
2,504 |
| 05/27/2025 04:09 PM |
Rick VanHatten |
Need to check internal dust collect path. It was blowing back more chips than it should have. Path dust collect from the machine port to the cyclone was good. |
Jointer 16 Inch Grizzly M12 |
Limited Functionality |
|
2,503 |
| 05/27/2025 04:05 PM |
Rick VanHatten |
Adjust fence stop to 90 degrees.it was off several degrees. |
Jointer 16 Inch Grizzly M12 |
In Service |
|
2,502 |
| 05/27/2025 12:31 PM |
Mike Makowski |
Repaired – motor repositioned to tighten rear belt. Back in service. |
Drill Press 18 Inch Delta M9 |
In Service |
|
2,501 |
| 05/27/2025 12:20 PM |
Nels Lundgren |
Replaced sand paper on drum sander M10. |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,500 |
| 05/27/2025 08:58 AM |
Patrick Duffy |
Updated Windows OS (shut down and restarted) the laptop associated with the 3D printer. Tested OK upon completion. Connected satifactorily with the 3D printer. |
3D Printer |
In Service |
|
2,499 |
| 05/26/2025 07:05 PM |
Mike Makowski |
Rear belt slips under high load |
Drill Press 18 Inch Delta M9 |
Limited Functionality |
|
2,498 |
| 05/26/2025 03:51 PM |
Bryan Blacksher |
Belt broke. Could not find a replacement in Deep Storage 7D. |
Drum Sander 25 Inch Supermax M10 |
Out of Service |
|
2,497 |
| 05/26/2025 03:13 PM |
Bryan Blacksher |
Several people ran pieces through the planer and found that the pieces did not feed on through and were VERY difficult or impossible to pull out without lowering the bed.
Don’t know what the problem could be. |
Planer 20 Inch General International M29 |
In Service |
|
2,496 |
| 05/24/2025 12:57 PM |
Nancy Bosecker |
James Ades was using a metal tape measure and activated the cartridge on Saw Stop 2. The blade was not embedded very deeply so when we removed and inspected it, it was not damaged. We replaced the cartridge with the new one from the cabinet and left the activated one on the Shift Supervisor desk. A new replacement cartridge should be ordered. |
Not a Tool Repair Issue |
In Service |
|
2,495 |
| 05/24/2025 10:32 AM |
Dan McNaughton |
36″ long craft paper behind bench 2. The cutoff bar missing a screw |
Not a Tool Repair Issue |
Limited Functionality |
|
2,494 |
| 05/23/2025 09:21 AM |
Paul Schankin |
3Dprinter not printing from laptop. Only way to print is to save file to FILENAME.gcode.3mf type file, load onto micro SD card and then print from SDcard at printer. Printer wants to update as MQTT error indicates so. |
3D Printer |
Limited Functionality |
|
2,492 |
| 05/23/2025 07:39 AM |
Paul Schankin |
Controller required resetting after not closing after time out. Monitor controller, HDM in service. |
CNC Shapeco HDM M4 |
In Service |
Yes |
2,490 |
| 05/21/2025 04:56 PM |
Jeff Bratt |
Electrical panel labeling . Drum Sander M10 – circuit breaker was tripped. Resetting it put the machine back in service. However, the label for M10 is wrong in the panel. The labels for E22 and E24 are correct. |
Not a Tool Repair Issue |
|
|
2,489 |
| 05/21/2025 04:00 PM |
Jerry Mackelburg |
The printer’s base plate was apparently changed from a “Cold Plate” to a “Textured PEI Plate” since last September. If the software doesn’t reflect that, the print probably won’t adhere to the plate. Is there an up-to-date version of the printer “workflow” available for users? |
3D Printer |
Limited Functionality |
|
2,488 |
| 05/20/2025 08:51 PM |
Scott Baldwin |
Unit does not power up. |
Drum Sander 25 Inch Supermax M10 |
Out of Service |
|
2,486 |
| 05/20/2025 08:36 PM |
Scott Baldwin |
Jointer is sniping at the end of an edge jointing |
Jointer 16 Inch Grizzly M12 |
Limited Functionality |
|
2,485 |
| 05/19/2025 07:55 PM |
Nels Lundgren |
Dust Collector did not shut off when in Auto, and no tools running.
Shut Off manually and tested again and it operated as expected.
A short time later, it started on its own with no tools running.
We observed the blast gate sensor for the manual gate near the lathe area/sheet good storage was malfunctioning; the LED readout flashing and the red indicator lamp was on. I gave it the magic touch and seemed to stop malfunctioning. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,484 |
| 05/19/2025 07:01 PM |
Nels Lundgren |
Oneida did not shut off with no tools running. Setting was Auto/Long Delay. Manually shut it off and set to Auto/Short Delay, turned on a machine and this time it shut off. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,483 |
| 05/18/2025 02:07 PM |
Nels Lundgren |
Recently replaced Drive belts were loose, and the pulleys would easily slip, slowing down or stopping the drill bit. Adjusted the motor mount position to tighten up. It is better, but the front belt is still a little on the loose side. |
Drill Press 18 Inch Delta M9 |
In Service |
|
2,482 |
| 05/18/2025 01:28 PM |
Rick VanHatten |
Restarted mesh router & is now reporting |
Disk/Belt Sander Jet M38 |
In Service |
|
2,481 |
| 05/18/2025 01:23 PM |
Rick VanHatten |
Batteries calipers for both planers are replaced. |
Mortiser Powermatic M27 |
In Service |
|
2,480 |
| 05/18/2025 01:19 PM |
Rick VanHatten |
Purchased complete bit set and placed in sustainer for the tool. |
Domino DF 500 Festool |
In Service |
|
2,479 |
| 05/18/2025 12:32 PM |
Paul Schankin |
Ref reports 2479, 2475 and 2474. ATT router reset affected mesh nodes downstream possibly causing issues. Blast gate controllers initializing dust collection auto on/off issues may be resolved. Monitor dust collection. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
Yes |
2,478 |
| 05/18/2025 06:01 AM |
Paul Schankin |
From 5/17/2025 shop slots. Reports of unreliable operation of auto turn on/turn off function of dust collector by machine blast gates. Manual operation of dust collector required. |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
2,477 |
| 05/17/2025 04:14 PM |
Mark Umphres |
50 degree bowl gouge is broken |
Hand Tools |
Out of Service |
|
2,476 |
| 05/17/2025 01:38 PM |
Duane Kuperus |
Dust collection drum level lights need to be calibrated |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,475 |
| 05/17/2025 11:57 AM |
Duane Kuperus |
Handheld router drawer needs attention. Some of the routers do not fit in their bases properly. One of the DeWalt routers (small) has a broken depth adjustment ring. None of the routers has a baseplate that will fit a medium ogee bit or larger. |
Not a Tool Repair Issue |
Limited Functionality |
|
2,474 |
| 05/17/2025 10:11 AM |
Paul Schankin |
Blast gate controller not reporting in HA as connected. Reset and rebooted controller, issue remains. Limited function of BG controller. |
Disk/Belt Sander Jet M38 |
Limited Functionality |
Yes |
2,473 |
| 05/17/2025 10:09 AM |
Paul Schankin |
Misc blast gate controller issues reported after ATT router required restarting. Ensure BG controllers, Blast Gates and Oneida is operating correctly as well as auto power off dust collection. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
Yes |
2,472 |
| 05/16/2025 09:31 AM |
Paul Schankin |
Rtr table #1, M30, not reporting in on HA. BG controller and BG, rtr table in service. |
Router Table #1 M30 |
In Service |
Yes |
2,471 |
| 05/15/2025 12:21 PM |
Duane Kuperus |
Replaced Belt and returned to service |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,470 |
| 05/15/2025 10:49 AM |
Duane Kuperus |
Need spare drum sander belts. Belt broke on M10 and no spares in the cabinet |
Supplies |
|
|
2,469 |
| 05/15/2025 10:48 AM |
Duane Kuperus |
Belt broke and there is not a spare belt. |
Drum Sander 25 Inch Supermax M10 |
Out of Service |
|
2,468 |
| 05/14/2025 03:38 PM |
Duane Kuperus |
On 5/13 Lou Cortellini and I performed table saw lube and clean service on the blade elevation and tilt mechanisms. Vacuumed the internal cabinet and verified the alignment of the rip fence to the miter slot. Confirmed the blade to table alignment is in spec (<.007) at .002. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,467 |
| 05/13/2025 12:04 PM |
Michael Ross |
The broken belt has been replaced. Both belts are new now. I’ll order an extra set for in the future. |
Drill Press 18 Inch Delta M9 |
In Service |
|
2,465 |
| 05/13/2025 09:01 AM |
Paul Schankin |
DC bag 80% full, replaced. |
Shop Vac Rigid |
In Service |
|
2,464 |
| 05/12/2025 08:02 PM |
Tom York |
The battery for the caliper of this machine has burned out…..needs to be replalced. |
Mortiser Powermatic M27 |
Limited Functionality |
|
2,462 |
| 05/12/2025 02:13 PM |
Bryan Blacksher |
When I came in, the barrel status indicator above the supervisors desk was flashing orange. I checked both barrels and they only had a couple of gallons of dust each. I wiped off both sensors hoping that would fix the problem. It did not. Now at 2:10pm both the orange and red lights are flashing with not much dust being created. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,460 |
| 05/09/2025 12:20 PM |
Nels Lundgren |
Bought sleeves of 50 sheets of 80 grit and 180 grit Surfprep (aluminum oxide) sand paper from EB Bradley for $18.25 each which is about 30% of the cost of the Norton ProSand sand paper. We will see how this paper performs and whether to continue buying it. |
Supplies |
In Service |
|
2,459 |
| 05/08/2025 06:59 PM |
Nels Lundgren |
missing the 4mm bit |
Domino DF 500 Festool |
Limited Functionality |
|
2,457 |
| 05/06/2025 11:28 AM |
Lou Cortellini |
Re-calibrated the Wixey gauge early this morning |
Planer 20 Inch General International M29 |
In Service |
|
2,454 |
| 05/06/2025 08:55 AM |
Paul Schankin |
Per report 2438, static pressure sensor is now being reported in HA, in service. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,453 |
| 05/05/2025 07:00 PM |
Skip Florey |
The DRO is not registering any height adjustment. I did reset by power on/off. The Wixie does register if moved manually. |
Planer 20 Inch General International M29 |
Limited Functionality |
|
2,451 |
| 05/05/2025 01:13 PM |
Nels Lundgren |
Disassembled the router lift and examined the condition of the threaded rod assembly. The top bearing moves as freely as the threaded rod assembly that was removed and replaced on router table #2 (M31), so I did not swap it out. I did rethread it into the two nuts on the lift and eliminated the lash that James Ade had reported. It is working pretty smoothly now, and the speed control is facing the front of the cabinet. |
Router Table #1 M30 |
In Service |
|
2,450 |
| 05/05/2025 01:07 PM |
Nels Lundgren |
Replenished 320 grit sheet sandpaper (1 – 20 sheet box) |
Supplies |
In Service |
|
2,449 |
| 05/04/2025 10:29 AM |
Nels Lundgren |
Refer to entry 2445 : Checked router lift and it is fine. A little sticky at the very top range when the collet is above the table, but otherwise it operates smooth enough throughout the range of travel. Not as smooth as router table #2 (M31) which recently was rebuilt with new threaded rod assembly and locking mechanism, but as smooth as we can get with the threaded rod assembly upper bearing not spinning freely.
Turned router around so that speed control faces the front of the cabinet. |
Router Table #1 M30 |
In Service |
|
2,447 |
| 05/04/2025 10:22 AM |
Nels Lundgren |
replenished 220 grit Sheet Sand paper (2 – 20 sheet boxes) and 400 grit Sheet Sandpaper (1 – 20 sheet box). |
Supplies |
In Service |
|
2,446 |
| 05/03/2025 08:51 PM |
Jerry Mackelburg |
Exhaust flapper is stuck open, drum fill indicator lights don’t work properly, rightmost drum cover is dented, and spare drum cover used by some to cover drums during transport is missing. |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
2,444 |
| 05/03/2025 08:45 PM |
Jerry Mackelburg |
Lift mechanism needs attention, and the router needs to be rotated 180 degrees to facilitate speed adjustment. |
Router Table #1 M30 |
Limited Functionality |
|
2,443 |
| 05/03/2025 08:30 PM |
Jerry Mackelburg |
Wixey display was dim and inaccurate. Replaced both AAA Lithium batteries (which measured 1.1V) installed on December 30th with alkalines, since it’s not clear that the Lithiums lasted any longer. Power/energy meter reading was 362 hrs and 428 kWhrs. 58 hrs and 71 kWhrs more than in December. Gauge recalibrated and tested. |
Planer 20 Inch General International M29 |
In Service |
|
2,442 |
| 05/03/2025 03:17 PM |
Jerry Mackelburg |
Drive belt torn |
Drill Press 18 Inch Delta M9 |
Out of Service |
|
2,441 |
| 05/03/2025 11:30 AM |
Duane Kuperus |
Changed sand paper and returned to service |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,440 |
| 05/03/2025 11:05 AM |
Duane Kuperus |
Battery need replaced on Wixey Gauge |
Planer 20 Inch General International M29 |
In Service |
|
2,439 |
| 05/03/2025 10:00 AM |
Oi Ling Kwan |
band snaped out of line when making deer with 2 in thick wood. replaced band with last bade in supply draw. please re-order. thanks |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,438 |
| 05/02/2025 11:13 AM |
Tom York |
The sandpaper has loosened on the roller. Needs to be tightened. |
Drum Sander 25 Inch Supermax M10 |
Limited Functionality |
|
2,437 |
| 05/02/2025 10:01 AM |
Nels Lundgren |
Purchased another Wixey angle gauge to replace the missing one. When I came in to put it in service I found the missing gauge had been moved to the new shelf by TS #2. So I put the second Wixey on the metal Flammables cabinet near TS #1 |
Supplies |
In Service |
|
2,436 |
| 05/02/2025 08:45 AM |
Paul Schankin |
Oneida static pressure sensor not reporting on Home Assistant dashboard but controller reads 9.4 Reset controller, still not being reported on dashboard. |
Not a Tool Repair Issue |
Limited Functionality |
Yes |
2,435 |
| 05/02/2025 08:38 AM |
Paul Schankin |
Controller stuck on “Booting” prompt with BG open. Pressed reset button, controller cycled and booted correctly. Cycled machine, machine and controller in service. |
Router Table #1 M30 |
In Service |
Yes |
2,434 |
| 04/29/2025 03:46 PM |
Nels Lundgren |
Replaced the threaded rod assembly and the locking mechanism assembly in the M31 Router Lift. Cleaned and lubricated the threads. The lift height adjustment and lock work like new.
The top bearing in the threaded rod assembly does not move freely, same problem as we had on M30, but not as bad, so I think we can make it better and keep it as a spare. The locking bar was worn out, I purchased an additional locking bar that we can use on the assembly that I replaced and keep it as a spare. Both the threaded rod and locking assembly that were replaced are in a box in the M30 cabinet lower shelf. Added it to the “Find Shop Items” App location system.
Also leveled the router lift plate with the router table. |
Router Table #2 Rockler M31 |
In Service |
|
2,433 |
| 04/29/2025 03:36 PM |
Nels Lundgren |
A couple more notes on the Drum Sander repair that Chris and I did:
When we disassembled the controller box we found the ground wires not secured, the nuts fell onto the floor. Also a metal shroud inside the controller box was never secured. It was just floating in there. We secured it.
Testing after replacing the controller board did not fix the problem. Only after pulling the brushes and cleaning them off did the motor work. Kept the old controller board as a spare, because believe it is good. Ordering new brushes.
Also the copper bushing used on the rod that is secured by the controller box was badly worn and replaced. Kept it if anyone wants to see.
Recommend we pull the controller box on M10 and check for similar issues, and examine the copper bushing for excessive wear. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,432 |
| 04/23/2025 05:17 PM |
Jeff Bratt |
Drive belt no longer runs. Drum motor turns, but the drive belt has stopped working. |
Drum Sander 25 Inch Supermax M11 |
Out of Service |
|
2,431 |
| 04/22/2025 12:25 PM |
Rick VanHatten |
Checked operation of Conveyor Belt and it worked fine. Ran material through with no problem. Its a mystery why it wasn’t working. Need to keep and eye on it. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,430 |
| 04/22/2025 12:07 PM |
Rick VanHatten |
Someone ran metal over the 16″ jointer. Required replacing 9 badly damaged inserts completely and rotating 4 one position. Dallas has the damaged inserts. Used the WD40 special penetrating light oil on the screws and torqued them to 50 in/lbs. Recommend that we send out the entire head to have a machinist remove the 4 insert positions with stripped/frozen screws. Machine is operational at this time. |
Jointer 16 Inch Grizzly M12 |
In Service |
Yes |
2,428 |
| 04/21/2025 06:30 PM |
Steve Carter |
Several badly chipped cutters, I know these were replaced recently but they need attention |
Jointer 16 Inch Grizzly M12 |
Limited Functionality |
|
2,427 |
| 04/19/2025 01:04 PM |
Duane Kuperus |
Digital Wixie gauge for table saw blade tilt is missing. |
Not a Tool Repair Issue |
In Service |
|
2,426 |
| 04/19/2025 12:21 PM |
Duane Kuperus |
Cleared Dust collection hose plug. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
Yes |
2,425 |
| 04/19/2025 11:09 AM |
Duane Kuperus |
Drum energizes and rotates. Belt drive will not energize. |
Drum Sander 25 Inch Supermax M11 |
Out of Service |
|
2,424 |
| 04/18/2025 09:47 AM |
Paul Schankin |
Per report 2424, numerous thin cutoffs were blocking the BG from operating. Removed obstruction, machine and blast gate in service. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
Yes |
2,423 |
| 04/17/2025 07:43 PM |
Scott Baldwin |
Blast gate reads error. Will not open |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
Out of Service |
Yes |
2,422 |
| 04/15/2025 11:48 AM |
Nels Lundgren |
Replaced the Lift Locking Assembly and un-froze the top bearing of the threaded rod assembly that raises and lowers the lift carriage. The top bearing is still not moving freely but is better. Incra tech support is looking for another threaded rod assembly to send us. cleaned and lubed the threaded rod assembly and reinstalled. The lift moves up and down much more easily. Will wait to hear back from Incra on the replacement threaded rod assembly. |
Router Table #1 M30 |
In Service |
|
2,420 |
| 04/15/2025 09:19 AM |
Paul Schankin |
Per report 2420, wired 3 button scroll mouse replaced. Machine in service. |
CNC Shapeco HDM M4 |
In Service |
|
2,419 |
| 04/14/2025 01:36 PM |
Patrick Duffy |
HDM PC is back on-line. CCWT (Came Clear While Testing).
The right mouse button is intermittent. The mouse should be replaced to restore full functionality.. |
CNC Shapeco HDM M4 |
In Service |
|
2,418 |
| 04/14/2025 09:38 AM |
Patrick Duffy |
Desktop PC will not boot. It will be replaced later today. |
CNC Shapeco HDM M4 |
Out of Service |
|
2,417 |
| 04/13/2025 02:39 PM |
Patrick Duffy |
Updated Vectric VCarve from 12.013 to 12.014. Added VCarve models to clipart tab. |
CNC Shapeco XXL M5 |
In Service |
|
2,416 |
| 04/13/2025 02:34 PM |
Rick VanHatten |
Replaced 4″ spindle with new. This significantly reduced the wobble to an acceptable level. Will replace the next 4 sizes down as well. |
Spindle Sander Enlon M33 |
In Service |
|
2,415 |
| 04/13/2025 02:13 PM |
Patrick Duffy |
Updated Vectric VCarve to fr5om 12.013 to 12.014. Added VCarve Model under the Clipart tab. |
CNC Shapeco HDM M4 |
In Service |
|
2,414 |
| 04/12/2025 07:27 PM |
Scott Baldwin |
Bandsaw blade broke. It was replaced with 111″ Olson. I believe machine is correctly adjusted and is running fine, but probably should be checked for correct operation. |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,413 |
| 04/11/2025 12:16 PM |
Rick VanHatten |
Broke a blade. Blade guard on riser was loose and contacted the blade. Screw holding the guard in place had the washer “behind” the attachment leaving it loose. Also out of blades, ordering more. For now installed a 3/8″ blade. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,410 |
| 04/11/2025 11:32 AM |
Rick VanHatten |
Lubricated lift |
Router Table #2 Rockler M31 |
In Service |
|
2,409 |
| 04/11/2025 11:31 AM |
Rick VanHatten |
Lubricated lift |
Router Table #1 M30 |
In Service |
|
2,408 |
| 04/11/2025 09:02 AM |
Paul Schankin |
Replaced large diameter spindle sandpaper. Machine in service. |
Spindle Sander Enlon M33 |
In Service |
|
2,407 |
| 04/10/2025 06:53 PM |
Nels Lundgren |
Replenished 320 grit sheet sand paper. Bought at TH&H @ $15.70 for a 20 sheet box |
Supplies |
In Service |
|
2,406 |
| 04/09/2025 10:57 AM |
Tom Roetker |
Rockler 3/16″ round over bit with a 1/2″ shaft was found at M30 behind fence. There is a large chip out of one of the carbide cutters. bit was marked with blue tape and put in the bottom of the router bit cabinet for replacement. |
Router Table #1 M30 |
In Service |
|
2,405 |
| 04/09/2025 10:52 AM |
Tom Roetker |
I got two cases of large gloves and one case of medium gloves from Palomar college. We were out of medium gloves in the bench and we don’t have any small. Each case has ten boxes of gloves. I restocked assembly table 2 with several boxes of large and medium. Still need small gloves for Assembly table 2 and will need XL soon. I put the extra boxes of gloves above the gray chemicals cabinet |
Supplies |
In Service |
|
2,404 |
| 04/08/2025 09:47 PM |
Rick VanHatten |
Replaced drive spindle. Complete disassembly and installed new spindle. Machine still has some wobble. Ordered a new 4 inch spindle to see if that improves the wobble. |
Spindle Sander Enlon M33 |
Limited Functionality |
|
2,403 |
| 04/08/2025 12:24 PM |
Tom Roetker |
Low on shop rags. ordered three 12 lb. boxes of HDX cotton rags. Extra stock is in the upper storage cabinet over mop closet. |
Supplies |
In Service |
|
2,402 |
| 04/07/2025 08:45 PM |
Ron Prater |
Jesse Bolane and I replaced all the cutter chips on the cutterhead, except for 5 that we couldn’t unscrew. This process involved breaking five T-20 Torx drivers that twisted or broke. The jointer produces an excellent cut now. |
Jointer 16 Inch Grizzly M12 |
In Service |
|
2,401 |
| 04/07/2025 04:01 PM |
Nels Lundgren |
Disregard last entry about needing another box of drum sander paper. I found another box in the tall cabinet |
Supplies |
In Service |
|
2,400 |
| 04/07/2025 03:57 PM |
Nels Lundgren |
We were all out of pre-cut drum sander paper, so cut four from the remaining roll. Need a new roll of drum sander paper. |
Supplies |
In Service |
|
2,399 |
| 04/07/2025 03:50 PM |
Nels Lundgren |
The Washer on the right side of the blade was installed backwards (with bevel side to the blade) causing the blade to be misaligned with the throat plate and riving knife by about a 1/16 of an inch. flipped the washer so that the flat side is against the blade and all good.
Also found the throat plate for saw#2 in the saw #1 cabinet. Although that doesn’t matter so much since the throat plates are no longer zero clearance. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,398 |
| 04/07/2025 02:42 PM |
Nels Lundgren |
Purchased 120, 150, 180, 220 grit Norton ProSand sandpaper packs from TH&H. 20 sheets per pack; 120, 150 are $21.42 per pack, 180, 220 are $15.70 per pack.
Low on 320, so I will pick some of that up this week |
Supplies |
In Service |
|
2,397 |
| 04/07/2025 02:38 PM |
Nels Lundgren |
Purchased three rolls of red rosin paper at home depot, in the closet by the office. $20,36 in x 166 ft each |
Supplies |
In Service |
|
2,396 |
| 04/05/2025 04:11 PM |
Mark Umphres |
In auto mode was coming on when no gates were open. Discussed with Rick VH and disconnected the gate controller to M23 (small spindle sander). Seems to be working now. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,395 |
| 04/05/2025 04:06 PM |
Mark Umphres |
Blade broke and was replaced. The saw seems to be working but the starter electronics are humming loudly. Currently unplugged |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,394 |
| 04/04/2025 12:18 PM |
Paul Schankin |
Newly installed controller does not show error, but relay is not opening, keeping Oneida running. Controller unplugged. Manual blast gate for now. |
Spindle Sander Powermatic M34 |
Limited Functionality |
Yes |
2,393 |
| 04/04/2025 10:53 AM |
Rick VanHatten |
Changed paper. Used the last spare roll. Members need to use the whole width of the drum. The “center” third on both drum sanders were worn down and the the rest of the paper was good. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,392 |
| 04/03/2025 08:43 PM |
Scott Baldwin |
some one put unusual item through drum sander causing unusual wear pattern in the sandpaper, which is reflected on any piece being run through sander. There may be damage to the sander as well, but unable to evaluate. |
Drum Sander 25 Inch Supermax M11 |
Out of Service |
|
2,391 |
| 04/03/2025 08:40 PM |
Scott Baldwin |
Someone put unusual item through both drum sanders, M10 and M11, damaging sandpaper. Paper on M10 replaced, didn’t have time to do M11. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,390 |
| 04/03/2025 04:29 PM |
Paul Schankin |
Controller throwing error code, keeping relay closed so that Dust collection never turns off. Removed defective controller, Oneida dust collection back in service. Reference report 2389. |
Spindle Sander Powermatic M34 |
In Service |
Yes |
2,389 |
| 04/03/2025 03:06 PM |
Gordon Stone |
tool lines left ion face grain of jointed wood |
Jointer 12 Inch Grizzly M16 |
In Service |
|
2,388 |
| 04/02/2025 10:41 PM |
Tom Roetker |
At the evening Luthier SIG the dust collector would not turn off. Had to power down the main power for the evening. Could not find any blast gates which were indicating open. Shift Supervisor will need to turn it on in the morning. |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
Yes |
2,387 |
| 04/02/2025 05:52 PM |
Ron Prater |
Last week I replaced 5 chips on the 16″ jointer cutterhead. Someone had run something hard into the cutters, maybe a screw. Four chips were badly damaged to the point where the chips lacked structural integrity and could not be rotated. Whoever damaged the cutters knew about it because some of the damaged chips were marked with a red marker, but no one reported the incident.
It seems that the new chips don’t fit exactly in the cutterhead. The new chips cut slightly deeper than the old chips, leaving flat grooves in the wood. Rick and I decided the best solution is to replace all the chips. Rick has ordered the new chips. But in the meanwhile the surface of machined wood will have grooves. |
Jointer 16 Inch Grizzly M12 |
In Service |
|
2,386 |
| 04/02/2025 04:01 PM |
Rick VanHatten |
Confirming Log is operational |
Test Tool |
In Service |
|
2,385 |
| 04/02/2025 01:30 PM |
Doug Murphy |
Wobble when drum rotating. Seems shafts not concentric in taper |
Spindle Sander Enlon M33 |
In Service |
|
2,384 |
| 04/02/2025 11:43 AM |
Tom Roetker |
lift mechanism is sticky and requires a bit of force to raise the router motor. |
Router Table #1 M30 |
Limited Functionality |
|
2,383 |
| 04/01/2025 02:05 PM |
Rick VanHatten |
Complete set of cutters ordered there is a complete new set |
Jointer 16 Inch Grizzly M12 |
Limited Functionality |
|
2,382 |
| 04/01/2025 02:01 PM |
Rick VanHatten |
Belt is fine, not great but still serviceable |
Edge Sander Jet M15 |
In Service |
|
2,380 |
| 04/01/2025 01:59 PM |
Rick VanHatten |
Tested all vacuum bags and found no leaks |
Vacuum Press |
In Service |
|
2,378 |
| 04/01/2025 09:31 AM |
Paul Schankin |
Approx 3/4 cup of water drained from air compressor tank. Machine in service. |
Air Compressor Fortress |
In Service |
|
2,377 |
| 04/01/2025 09:02 AM |
Paul Schankin |
Per report 2371. Replaced time delay off relay for CNC chiller AC supply. Chiller automatically turns off after 10 minute cool down time for spindle. Machine in service. |
CNC Shapeco HDM M4 |
In Service |
|
2,376 |
| 03/31/2025 01:43 PM |
Bryan Blacksher |
Lights above SS workstation were flashing alternately green and orange, and then orange and red. Shut down work and checked the barrels. Only about 1/6 full. The problem is the rain. It has gotten inside the enclosure up above and then dripped down onto the left barrel.
The water went through the hole that the sensor is in and got the bottom of the sensor wet, which then collected dust, giving a false reading. I would recommend the sensor hole be caulked, to prevent this problem. Currently ignoring the lights above the workstation.
Also, the rain is getting the plywood up above wet, which will over time weaken the plywood and cause worse problems. Maybe the enclosure needs louvers on the outside of the openings. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,375 |
| 03/31/2025 10:58 AM |
Patrick Duffy |
Loud spindle noise is generated while cutting. This may be a spindle bearing. Machine appears to cut correctly. Temporary solution is to reduce the depth of cut (DOC)/depth per pass. Test was done with a 1/4″ flat endmill running at 75IPM and 18,000RPM. Original DOC was 0.1″. Reduced the DOC to 0.5″ and much of the noise was mitigaed. I will continue to test when I return to San Diego. |
CNC Shapeco XXL M5 |
In Service |
|
2,374 |
| 03/30/2025 11:23 AM |
Paul Schankin |
Dust collection barrel indicator amber light is blinking, dust barrels are 5% full. Indicator lights need calibrating. Machine in service. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,373 |
| 03/30/2025 11:20 AM |
Paul Schankin |
Report of dust collection enclosure light not working. AC plug not inserted completely. Inserted plug, light working. |
Not a Tool Repair Issue |
In Service |
|
2,372 |
| 03/29/2025 07:40 PM |
Jerry Mackelburg |
Getting low on SoftSoap |
Supplies |
In Service |
|
2,371 |
| 03/29/2025 12:10 PM |
Paul Schankin |
Per #2371. Chiller working as plugged into switched outlet. Will replace time delay off relay when part received. HDM in service. |
CNC Shapeco HDM M4 |
In Service |
|
2,370 |
| 03/28/2025 12:29 PM |
Rick VanHatten |
Chiller does not shut off. Unplugged from wall outlet |
CNC Shapeco HDM M4 |
Limited Functionality |
|
2,369 |
| 03/28/2025 12:28 PM |
Rick VanHatten |
test |
Supplies |
In Service |
|
2,368 |
| 03/28/2025 12:06 PM |
Rick VanHatten |
test |
Supplies |
Limited Functionality |
|
2,367 |
| 03/28/2025 12:01 PM |
Rick VanHatten |
test |
Supplies |
In Service |
|
2,366 |
| 03/27/2025 09:23 PM |
Nels Lundgren |
Replaced the paper on the drum sander. There are three spare precut rolls remaining in the drawer. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,365 |
| 03/27/2025 09:20 PM |
Nels Lundgren |
Picked up two sharpened table saw blades from Frost today. |
Supplies |
In Service |
|
2,364 |
| 03/27/2025 03:30 PM |
Tom Roetker |
There looks to be resin patch on it and may need to be replaced./ I could not remove with the eraser |
Edge Sander Jet M15 |
Limited Functionality |
|
2,363 |
| 03/25/2025 08:54 AM |
Paul Schankin |
Entry way monitor required system update. Updated monitor, monitor in service. |
Not a Tool Repair Issue |
In Service |
|
2,361 |
| 03/24/2025 03:45 PM |
Phil Silverstone |
1/2″ spindle needs new sandpaper |
Spindle Sander Enlon M33 |
In Service |
|
2,360 |
| 03/22/2025 12:44 PM |
Rick VanHatten |
Cord cap replaced |
Router Table #2 Rockler M31 |
In Service |
|
2,359 |
| 03/22/2025 12:10 PM |
Duane Kuperus |
Toilet seat in the downstairs bathroom is broken off |
Not a Tool Repair Issue |
Limited Functionality |
|
2,358 |
| 03/22/2025 10:42 AM |
Skip Florey |
Cutter is leaving a proud grove about 9″ from fence. cutters need to be rotated |
Jointer 16 Inch Grizzly M12 |
Limited Functionality |
|
2,357 |
| 03/21/2025 08:35 AM |
Tom Roetker |
Chipped insert at about 7.5″ from outside edge of table. Found by Dara |
Jointer 16 Inch Grizzly M12 |
Limited Functionality |
|
2,355 |
| 03/21/2025 08:12 AM |
Paul Schankin |
Acrylic gate stuck, not closing completely. Disconnected attachment pins, cycled gate manually, reconnected and rebooted controller, blast gate functioning. |
Band Saw 14 SE Laguna M3 |
In Service |
Yes |
2,354 |
| 03/20/2025 09:54 AM |
Lynn Welling |
Blast gate unresponsive. can manually open/close by hand turning screw, o/w doesn’t respond to unit off or on. |
Band Saw 14 SE Laguna M3 |
In Service |
Yes |
2,353 |
| 03/19/2025 04:27 PM |
Jeff Bratt |
Blast gate is always open – controller says open |
Band Saw 14 SE Laguna M3 |
In Service |
Yes |
2,352 |
| 03/19/2025 02:24 PM |
Doug Murphy |
Need more 220 sand paper |
Not a Tool Repair Issue |
|
|
2,351 |
| 03/18/2025 09:12 AM |
Paul Schankin |
DC bag replaced, 80% full. Last replaced 1/30/2025 |
Shop Vac Rigid |
In Service |
|
2,349 |
| 03/18/2025 09:10 AM |
Paul Schankin |
DC bag at 80%, replaced bag. Last replaced 1/31/2025 |
Shop Vac Craftsman |
In Service |
|
2,348 |
| 03/16/2025 02:27 PM |
Patrick Duffy |
Replaced PC. The fan in the “old” one was making noise. All relavant applications have been installed. The replacement computer computer name is “CNC-HDM”. The defective PC is on the white shelved for Dave Hubbard to take a look at. |
CNC Shapeco HDM M4 |
In Service |
|
2,347 |
| 03/15/2025 08:08 PM |
Jerry Mackelburg |
The amber sawdust drum level light illuminated when the leftmost drum was about 1/4 full because of excessive buildup toward its front edge. The rightmost drum was about 1/2 full at the time. Maybe rotating the drum cover would help? |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
2,346 |
| 03/15/2025 07:54 PM |
Jerry Mackelburg |
The defective quick release lever on the vertical clamp reported as not working in Rpt. No. 2343 was re hot glued to make it usable without the quick release function again. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,345 |
| 03/15/2025 05:26 PM |
Jerry Mackelburg |
The computer was making an unsettling noise, so it was turned off with the terminal strip. |
CNC Shapeco HDM M4 |
Out of Service |
|
2,344 |
| 03/15/2025 02:55 PM |
Dana Chapin |
One of the hold downs is not working. Placed it on the office desk |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,341 |
| 03/14/2025 05:04 PM |
Rick VanHatten |
Replaced drum motor couplings. Spare couplings are in Shallow Storage 14B |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,339 |
| 03/14/2025 09:11 AM |
Paul Schankin |
Lift mechanism jackscrews need cleaning/lubrication. Difficult to adjust height of router bit. |
Router Table #1 M30 |
Limited Functionality |
|
2,338 |
| 03/14/2025 09:03 AM |
Sharon Sykora |
band saw blade broke while cutting 1/4″ thick wood. Blade replaced |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,337 |
| 03/12/2025 04:21 PM |
Jeff Bratt |
Blast gate extends too far forward over the fence – interferes with workpieces. Mount should be rotated or reconfigured. |
Jointer 12 Inch Grizzly M16 |
In Service |
|
2,336 |
| 03/11/2025 08:17 PM |
Rick VanHatten |
Drive couplings are on order with an expected delivery of Thursday, March 11th. I left a small puller by the couplers if they are needed to replace them. |
Drum Sander 25 Inch Supermax M10 |
Out of Service |
|
2,335 |
| 03/11/2025 08:15 PM |
Rick VanHatten |
The reason the conveyor belt wasn’t tracking was the bushings on the infeed side were worn to point of failing. Replaced the bushings. Still need to keep an eye on the tracking. It looks like the oilite bushings need to be replaced one a regular schedule. There there 8 more in the Drum Sander supplies shallow storage drawer. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,334 |
| 03/10/2025 07:23 PM |
Steve Carter |
conveyor belt is slipping and is tracking off center, I adjusted the tension on the belt and appears to be doing better |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,333 |
| 03/09/2025 10:20 AM |
Nels Lundgren |
Both the router lift plate and the miter channel were not flush with the router table causing pieces to catch at the transition. Adjustment screws on lift plate were ineffective because of wear to the cutout that it fits into. Adding backing to both the router lift cutout and the miter channel dado to level them to the table. |
Router Table #1 M30 |
In Service |
|
2,332 |
| 03/08/2025 08:37 PM |
Dallas Keck |
The electrical cord form the switch is missing a prong. The cord or the switch must be replaced |
Router Table #2 Rockler M31 |
Out of Service |
|
2,331 |
| 03/08/2025 03:01 PM |
Mark Umphres |
roborock sweeper came on at 2::20 pm on 3/8/24. was interfering with woodworker at table saw. I turned the power off and placed it next to the charging station. |
Not a Tool Repair Issue |
|
|
2,330 |
| 03/08/2025 01:39 PM |
Duane Kuperus |
Motor to drum coupling spacer is broke. Needs replacement/repair. |
Drum Sander 25 Inch Supermax M10 |
Out of Service |
|
2,329 |
| 03/08/2025 12:49 PM |
Duane Kuperus |
replaced batteries in remote for the bench room blinds and all is god now. |
Not a Tool Repair Issue |
In Service |
|
2,328 |
| 03/08/2025 11:18 AM |
Duane Kuperus |
Blinds in the bench room will not open using the remotes. Batteries seem good. |
Not a Tool Repair Issue |
Out of Service |
|
2,327 |
| 03/07/2025 11:21 AM |
Rick VanHatten |
Put broken clamp in trash |
Hand Tools |
In Service |
|
2,326 |
| 03/06/2025 09:15 PM |
Nels Lundgren |
All out of rags |
Supplies |
Out of Service |
|
2,325 |
| 03/06/2025 07:38 PM |
Nels Lundgren |
Adjusted the miter saw zero angle detent to be square |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,324 |
| 03/06/2025 06:00 PM |
Nels Lundgren |
Rebooted the blast gate on TS#2 and cycled on and off twice with no problem |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
Yes |
2,323 |
| 03/06/2025 04:14 PM |
Gordon Stone |
Saw #2 blast gate doesn’t open gives error message. Pulled out connectyor and plugged back in. Reboot message, tries to close blast gate’ doesn’t close and another error message |
Dust Collector 7.5 HP Oneida M14 |
Out of Service |
Yes |
2,322 |
| 03/06/2025 02:38 PM |
Gordon Stone |
I broke a 48″ Rockler Bar Clamp cranking it too tight |
Hand Tools |
Out of Service |
|
2,321 |
| 03/06/2025 08:05 AM |
Rick VanHatten |
Replaced motor controller. Things appear to be working but still some questions. Need to keep an eye on it. |
Laser Thunder Nova 35 M18 |
In Service |
|
2,320 |
| 03/06/2025 08:03 AM |
Rick VanHatten |
Belt Replaced a while back |
Edge Sander Jet M15 |
In Service |
|
2,319 |
| 03/05/2025 02:48 PM |
Doug Murphy |
Sounds like bearing may be going. Metalic clicking sound when drum is running. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,318 |
| 03/03/2025 04:21 PM |
Bryan Blacksher |
The orange light of the new 3 light indicator was on. Checked the barrels; less than 1/3 full.
Continued with shop operations. At end of shift I emptied the barrels. When I came back in both the green and red lights were on. Went out and dusted off and blew off the sensors but the left sensor still showed a small orange light while the right sensor showed green. Inside, the green and red sensors were still on. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,317 |
| 03/02/2025 08:02 PM |
Jerry Mackelburg |
Cleaned the gunk off the cutterhead and its casting as well as the infeed & outfeed rollers. Lubricated the four table height adjustment leadscrews with spray lithium grease and outside of their columns with Ron’s 3in1 oil (thanks/sorry Ron!). Rewaxed tables/rollers and checked the Wixey thickness gauge calibration. |
Planer 20 Inch General International M29 |
In Service |
|
2,316 |
| 03/02/2025 12:48 PM |
Jerry Mackelburg |
After checking the laser exhaust blower again today, I determined that I may have not waited long enough yesterday for it to fully start. Although it still sounds like it’s struggling to start, it eventually did start today. |
Not a Tool Repair Issue |
Limited Functionality |
|
2,315 |
| 03/01/2025 09:21 PM |
Jerry Mackelburg |
Before the 2:00PM shift today the rightmost drum was overflowing and leftmost was less than 1/2 full. Maybe one of the fullness sensors (like the amber ~1/2 full sensor) should be relocated to the right drum? Some people may not realize that they are infrared sensors and would probably work better if their lenses were wiped off before closing the drum lids? Wouldn’t mounting casters to the bottom of each drum make life easier and less problematic than the current cart? |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
2,314 |
| 03/01/2025 09:00 PM |
Jerry Mackelburg |
Laser exhaust blower isn’t working. |
Not a Tool Repair Issue |
Out of Service |
|
2,313 |
| 03/01/2025 08:52 PM |
Jerry Mackelburg |
Replaced Gear Box oil (with Valvoline 80W-90 Gear Oil again after almost 2 years) at 337 hrs. and 396 kWhr on power/energy meter. Cleaned and regreased feed roller drive chains and table height adjustment rack and pinion gear. Cleaned and waxed tables and table rollers. Oiled feed roller bushings. |
Planer 20 Inch General International M29 |
In Service |
|
2,311 |
| 02/28/2025 12:16 PM |
Rick VanHatten |
In feed table is significantly lower and angle down. Need to figure out how to raise up and level. M10 has a different design that is ok. This machine is the new one with cheaper infeed/outfeed tbles |
Drum Sander 25 Inch Supermax M11 |
Limited Functionality |
|
2,310 |
| 02/28/2025 12:11 PM |
Rick VanHatten |
test |
Sanding Station M05 |
In Service |
|
2,309 |
| 02/28/2025 11:30 AM |
Mary Russo |
Broken Blade, Relaced by Mary Russo |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,308 |
| 02/28/2025 10:53 AM |
Rick VanHatten |
Band saw blade change. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,306 |
| 02/28/2025 07:51 AM |
Paul Schankin |
Laser exhauster control module replaced. Exhauster in service. |
Not a Tool Repair Issue |
In Service |
|
2,305 |
| 02/27/2025 02:26 PM |
Tom Roetker |
Only one offset collet wrench available between the two router tables |
Router Table #2 Rockler M31 |
In Service |
|
2,302 |
| 02/24/2025 01:35 PM |
Phil Silverstone |
Dallas, Jim M. dropped off the small CNC router that you had discussed with him. It is in the closet in the office. |
Not a Tool Repair Issue |
|
|
2,301 |
| 02/23/2025 06:59 PM |
Wesly Berneberg |
Blade broke, replaced. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,300 |
| 02/23/2025 02:35 PM |
Nels Lundgren |
Top Ceramic guide needs adjusting. The blade is touching the left side of the ceramic guide and the right side is a gap. It’s evident that the blade is touching the guide, when raising and lowering the blade guard. The blade moves up and down with the guard. It may be an guard alignment issue because the blade does not move freely when the guard is raised up, but when the guard is close to the table, the blade moves freely. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,299 |
| 02/22/2025 01:25 PM |
Duane Kuperus |
Detent is off slightly for 90 degree cut. Needs to be adjusted and set manually for accurate 90 degree cut. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,298 |
| 02/22/2025 12:01 PM |
Duane Kuperus |
Need Band Clamps the function properly. The ones on table 2/4C will not tighten properly. |
Supplies |
In Service |
|
2,297 |
| 02/21/2025 10:21 AM |
Paul Schankin |
Replaced AC plug, machine back in service. |
Router Table #1 M30 |
In Service |
|
2,296 |
| 02/20/2025 04:08 PM |
Gordon Stone |
New belt located, belt replaced and tracking adjusted |
Disk/Belt Sander Jet M38 |
In Service |
|
2,294 |
| 02/20/2025 02:40 PM |
Gordon Stone |
replacement sanding belt for Jet M36 not found |
Disk/Belt Sander Jet M38 |
Out of Service |
|
2,293 |
| 02/20/2025 02:36 PM |
Gordon Stone |
torn belt – no replacement found |
Disk/Belt Sander Jet M38 |
Out of Service |
|
2,292 |
| 02/20/2025 11:21 AM |
Mike Makowski |
Defective plug – lost a prong |
Router Table #1 M30 |
Out of Service |
|
2,291 |
| 02/20/2025 09:45 AM |
Paul Schankin |
Poor vacuum at fittings for orbital sanders. Dust deputy bin has cracked lid, taped crack, marginal improvement at DC ports. Order new dust deputy lid if possible. Limited functionality. |
Sanding Station M05 |
Limited Functionality |
|
2,290 |
| 02/20/2025 08:56 AM |
Paul Schankin |
14 gallon Rigid shop vac. Replaced dust collection bag, 75% full, last replaced Aug 2024. Machine in service. |
Shop Vac Rigid |
In Service |
|
2,289 |
| 02/20/2025 08:39 AM |
Paul Schankin |
Per report 2287. Ensure “Machine Power” button is depressed for computer to connect to CNC. Ran test job, could not duplicate issue, machine in service. |
CNC Shapeco HDM M4 |
In Service |
|
2,288 |
| 02/19/2025 06:33 PM |
Chris Noone |
Drum sander belt was replaced. Not sure who did it but belt was installed properly. |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,287 |
| 02/19/2025 06:05 PM |
Ron Prater |
16″ jointer new to us is now in service. The wheels for adjusting the infeed and outfeed tables have been removed, and the depth of cut is a little less than 1/16″. Some work on the cutter chips is still needed. I’ll do that soon, but it works well in the meanwhile. |
Jointer 16 Inch Grizzly M12 |
In Service |
|
2,286 |
| 02/19/2025 03:00 PM |
Doug Murphy |
Computer won’t connect |
CNC Shapeco HDM M4 |
Out of Service |
|
2,285 |
| 02/19/2025 10:52 AM |
Paul Schankin |
User reported overhead light not working. Rocker power switch for light had been turned off. Turned light power switch on, machine in service. |
CNC Shapeco HDM M4 |
In Service |
|
2,284 |
| 02/19/2025 10:49 AM |
Paul Schankin |
Power supply for Jace controller, WS3, defective. Replaced power supply, system operational. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,283 |
| 02/19/2025 04:40 AM |
Duane Kuperus |
On 2/18 – Lubricated the #2 SawStop table saw blade elevation and tilt gears and bearing surfaces. Vacuumed the cabinet internals. Cleaned 3 table saw blades and sent two in for sharpening. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,282 |
| 02/17/2025 06:15 PM |
Mike Makowski |
Dust collection doesn’t turn on with turn on of power tool. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,281 |
| 02/17/2025 02:26 PM |
Bryan Blacksher |
The belt on drum sander M10 is pretty bad and needs to be replaced.
Did not find any pre-cut belts in deep storage 7E. |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,280 |
| 02/16/2025 09:33 PM |
Wesly Berneberg |
Auto ON/OFF does not function. Used the dust collection manually. |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
2,278 |
| 02/15/2025 08:56 PM |
Jerry Mackelburg |
A broken carbide cutter insert was replaced with one of the spares. The replacement was
marked with white paint on the cutterhead. The fence was moved to cover the first 2″ – 3″ of the cutterhead because it wasn’t cutting well. |
Jointer 12 Inch Grizzly M16 |
Limited Functionality |
|
2,277 |
| 02/13/2025 01:04 PM |
Paul Schankin |
Fume extraction intermittant, out of service. |
Laser Thunder Nova 51 M19 |
Out of Service |
|
2,272 |
| 02/13/2025 01:04 PM |
Paul Schankin |
Fume extraction intermittant, out of service. |
Laser Thunder Nova 35 M18 |
Out of Service |
|
2,271 |
| 02/12/2025 04:09 PM |
Patrick Duffy |
There appears to be a lens alignment issue. When a pulse command is issued, the result is an elongated line (about 1/8″ wide) instead of a dot. The issue distorts a cut-through line when the emphasis is along the Y axis so that the line is broader than the cut.
The system still works, but the quality of work might be inferior. |
Laser Thunder Nova 35 M18 |
Limited Functionality |
|
2,270 |
| 02/08/2025 10:27 PM |
Nels Lundgren |
Replaced broken band saw blade. Have one left in the cabinet and Rick has ordered 4 more, due to arrive in 10 days. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,267 |
| 02/08/2025 10:03 PM |
Jerry Mackelburg |
Cutoffs were removed from under the kerf plate and an obstruction was removed from under the rotating table that was limiting its rotation. A snap ring is missing from one of the two vertical clamps that makes it difficult to use. |
Miter Saw 12 Inch Makita M26 |
Limited Functionality |
|
2,266 |
| 02/08/2025 09:54 PM |
Jerry Mackelburg |
The Wixey gauge needed re-calibration, and the infeed bed roller needed to have an obstruction removed. |
Planer 20 Inch General International M29 |
In Service |
|
2,264 |
| 02/08/2025 01:52 PM |
Patrick Duffy |
The green “Normal” LED is not illuminated on the chiller. There is no alarm. Water appears to be flowing properly. I suspect that the LED circuit is not funtioning properly. |
Laser Thunder Nova 35 M18 |
In Service |
|
2,263 |
| 02/08/2025 09:31 AM |
Oi Ling Kwan |
blast gate does not open, no vacuuming |
Router Table #2 Rockler M31 |
Limited Functionality |
Yes |
2,262 |
| 02/04/2025 02:39 PM |
Rick VanHatten |
Replaced 3 conveyor belt bushings. Didn’t replace drive motor bushing. Will purchase additional. Also need to lubricate bushings periodically. Possibly monthly along with general inspection per manual. |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,260 |
| 02/02/2025 09:17 PM |
Nels Lundgren |
Adjusted conveyor belt tracking, but broken bushing causes conveyor to track to the left, and will likely result in damage to the conveyor belt. So putting out of service |
Drum Sander 25 Inch Supermax M10 |
Out of Service |
|
2,259 |
| 02/02/2025 04:35 PM |
Nels Lundgren |
A brass bushing on the end of one of the rollers of the conveyor is broken and needs replacing. This can cause the conveyor belt to not track straight and get damaged |
Drum Sander 25 Inch Supermax M10 |
Limited Functionality |
|
2,258 |
| 02/01/2025 09:24 PM |
Nels Lundgren |
Blade was dull, burning wood. Replaced with new blade and tensioned |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,255 |
| 02/01/2025 04:27 PM |
Jerry Mackelburg |
Belt tracking needs to be adjusted |
Drum Sander 25 Inch Supermax M10 |
Limited Functionality |
|
2,253 |
| 01/31/2025 09:00 AM |
Paul Schankin |
Replaced DC bag on Festool dust collection. Machine in service. |
Sanding Station M05 |
In Service |
|
2,252 |
| 01/31/2025 08:28 AM |
Paul Schankin |
Blast gate controller not opening BG. Manual blast gate operation required. Limited function. |
Router Table #2 Rockler M31 |
Limited Functionality |
Yes |
2,251 |
| 01/30/2025 09:11 PM |
Chris Noone |
Conveyor belt replaced, tensioned and tracking was checked. Belt spindle was checked for being level and the belt was cleaned. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,250 |
| 01/30/2025 07:49 PM |
Nels Lundgren |
Replaced bag. It was so full I couldn’t get it out without ripping it! |
Shop Vac Rigid |
In Service |
|
2,249 |
| 01/30/2025 06:41 PM |
Nels Lundgren |
Excessive leakage at the blast gate interface with the pipes |
Drum Sander 25 Inch Supermax M10 |
In Service |
Yes |
2,248 |
| 01/30/2025 01:30 PM |
Duane Kuperus |
Need new brake as there is no spare brake. Installed the last one on #2 saw. |
Supplies |
In Service |
|
2,247 |
| 01/30/2025 01:29 PM |
Duane Kuperus |
Found saw blade brake driven into blade. Brake adjustment screw would not loosen. Due to over tightening the brake adjustment screw and not due to activation. Was able to remove blade and brake. Used WD40 to lubricate brake adjustment screw. Reinstalled with new blade and brake. All working now. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,246 |
| 01/29/2025 04:29 PM |
Ron Prater |
tool does not trigger the dust collector; electronic box says “error”. Users need to briefly turn on some other tool in order to trigger the dust collector. |
Router Table #2 Rockler M31 |
In Service |
Yes |
2,245 |
| 01/29/2025 12:00 PM |
Paul Schankin |
Blast gate reads “Error Code 1” and does not open with power switched on. Correction…replaced blast gate actuator assy, not blast gate. |
Router Table #2 Rockler M31 |
In Service |
Yes |
2,244 |
| 01/29/2025 11:17 AM |
Paul Schankin |
Blast gate was not completely opening or closing, indicating Error Code #1 on controller. Replaced blast gate and verified machine in service. |
Router Table #2 Rockler M31 |
In Service |
Yes |
2,243 |
| 01/28/2025 05:14 PM |
Rick VanHatten |
New conveyor belt arrived. Chris Noone is installing this week |
Drum Sander 25 Inch Supermax M11 |
Out of Service |
|
2,241 |
| 01/28/2025 05:10 PM |
Rick VanHatten |
Joe P & Scott repaired top door hinge |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,240 |
| 01/28/2025 05:03 PM |
Scott Baldwin |
one of the shoulder planes, usually on the tool wall, is missing |
Hand Tools |
Out of Service |
|
2,239 |
| 01/26/2025 03:41 PM |
Rick VanHatten |
Test: Belt/Disk M6 Tool added to Shop Log (previously emails would not go thru) |
Belt/Disk Sander Jet M6 |
In Service |
|
2,238 |
| 01/26/2025 11:25 AM |
Rick VanHatten |
Auto start isn’t working. Use manual switch on the side with the vacuum to start and stop. |
Sanding Station M05 |
Limited Functionality |
|
2,237 |
| 01/26/2025 11:24 AM |
Rick VanHatten |
Dust collection blockage removed |
Router Table #2 Rockler M31 |
In Service |
|
2,236 |
| 01/25/2025 09:19 PM |
Jerry Mackelburg |
The shop log isn’t being updated adequately to reflect the current status of the equipment. The “Tool” filter doesn’t work. |
Not a Tool Repair Issue |
Limited Functionality |
|
2,235 |
| 01/25/2025 09:08 PM |
Jerry Mackelburg |
Empty classroom heat was set to 70 degrees this afternoon. |
Not a Tool Repair Issue |
In Service |
|
2,234 |
| 01/25/2025 02:17 PM |
Jerry Mackelburg |
Re-calibrated Wixey thickness gauge. |
Planer 20 Inch General International M29 |
In Service |
|
2,233 |
| 01/25/2025 08:32 AM |
Chris Noone |
test for Chris |
Disk/Belt Sander Jet M38 |
In Service |
|
2,232 |
| 01/22/2025 06:37 PM |
Rick VanHatten |
Tim, this is the an example of the Shop Log Entry you will receive when someone makes and Entry. We can look at this Shop Log on Tuesday and I can answer any question. You should make an Entry noting the work you did on Tuesday & Thanks. Rick |
Router Table #1 M30 |
In Service |
|
2,231 |
| 01/22/2025 06:34 PM |
Rick VanHatten |
Test Message – Chris Noone is now handling Sanders. Time, this is the typical email message when someone makes a shop log entry about on the sanders. Drum, Edge, Spindle & Belt/Disc. See you Saturday & thanks. Rick |
Belt/Disk Sander Jet M6 |
In Service |
|
2,230 |
| 01/22/2025 01:43 PM |
Jerry Mackelburg |
Wixey gauge was within calibration tolerance this afternoon. |
Planer 20 Inch General International M29 |
In Service |
|
2,227 |
| 01/22/2025 11:57 AM |
Patrick Duffy |
Updated VCarve Pro Makerspace Edition to V12.013 |
CNC Shapeco XXL M5 |
In Service |
|
2,226 |
| 01/22/2025 11:56 AM |
Patrick Duffy |
Updated VCarve Makerspace Edition to V12.013 |
CNC Shapeco HDM M4 |
In Service |
|
2,225 |
| 01/20/2025 07:12 PM |
Mike Makowski |
Sensor out of calibration |
Planer 20 Inch General International M29 |
In Service |
|
2,223 |
| 01/18/2025 09:24 AM |
Dan McNaughton |
When I arrived for 8:00am Sat 1\18
2025 the trash bin in parking lot was unlocked.
locked it after emptying Cyclone |
Not a Tool Repair Issue |
In Service |
|
2,222 |
| 01/17/2025 12:59 PM |
Jerry Mackelburg |
Feed belt torn – replacement to be ordered |
Drum Sander 25 Inch Supermax M11 |
Out of Service |
|
2,220 |
| 01/17/2025 09:57 AM |
Sharon Sykora |
Band saw blade broken and replaced. Door still broken. |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,219 |
| 01/16/2025 08:31 PM |
Nels Lundgren |
Spindle Sander Blast Gate opens, but not trigger the dust collector to turn on |
Spindle Sander Enlon M33 |
In Service |
Yes |
2,218 |
| 01/16/2025 02:25 PM |
Paul Schankin |
Cleared filament broken in AMS, reel #3, between infeed port and AMS filament selector. Machine in service. |
3D Printer |
In Service |
|
2,217 |
| 01/15/2025 02:00 PM |
Tom York |
The dust collections within the saw is collged. |
Router Table #2 Rockler M31 |
Out of Service |
Yes |
2,216 |
| 01/14/2025 03:46 PM |
Patrick Duffy |
Repaired the intermittent operation of the “Spindle Enable” LED. Replaced the femail half of the cable connector immediately adjacent to the “spindle Enable” switch. |
CNC Shapeco HDM M4 |
In Service |
|
2,215 |
| 01/11/2025 11:47 AM |
Duane Kuperus |
Dust collection drums (specifically the left drum) are out of round. The left drum is very much so and making it very difficult to put on the lid after emptying. “Massaged” the drum to back to close to round and now it seals with some effort. Someone placed a sign in the left drum to not empty due to the problem but that is not the solution. Also the left drum lid indicated it has been beaten with a hammer to make fit. Checked both drums and they were full to overflow. Emptied both drums. Recommend getting new drums and cover so the system works correctly. |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
2,213 |
| 01/11/2025 08:17 AM |
Paul Schankin |
Replaced dust collection bag, 80% full. Machine in service. Bag last replaced 8/13/2024. |
Dust Extractor Bosch |
In Service |
|
2,212 |
| 01/10/2025 02:43 PM |
Skip Florey |
Blast gate not opening and the tool is indicating it needs a brake adjustment |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
Out of Service |
Yes |
2,211 |
| 01/10/2025 08:57 AM |
Paul Schankin |
Replaced AC plug, machine in service. |
Dust Extractor Bosch |
In Service |
|
2,210 |
| 01/08/2025 04:14 PM |
Jeff Bratt |
Blast gate / current sensor on Delta jointer not working. Gate is open and display says Error. Does not trigger dust collector to turn on. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
Yes |
2,209 |
| 01/08/2025 01:53 PM |
Doug Murphy |
Jointer head has chipped cutter, still works fine. |
Jointer 12 Inch Grizzly M16 |
In Service |
|
2,208 |
| 01/07/2025 12:43 PM |
Paul Schankin |
Bad AC plug |
Dust Extractor Bosch |
Out of Service |
|
2,207 |
| 01/06/2025 03:09 PM |
Rick VanHatten |
Test tool only, not blast gate |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,204 |
| 01/06/2025 03:05 PM |
Rick VanHatten |
test |
Band Saw 14 SE Laguna M3 |
In Service |
Yes |
2,203 |
| 01/03/2025 07:52 AM |
Patrick Duffy |
Repaced the Carbide Motion PCB controller. The holding power on the X and Y axis appears to have improved with the new controller. Tested OK upon replacement.
Previous Version: 2.4f
New Version: 2/4g
|
CNC Shapeco XXL M5 |
In Service |
|
2,201 |
| 12/31/2024 11:06 AM |
Dallas Keck |
TESTING (code updates) |
Not a Tool Repair Issue |
In Service |
Yes |
2,200 |
| 12/30/2024 04:41 PM |
Jerry Mackelburg |
Rpt.No. 2192 suggested that the Wixey digital planer thickness gauge’s calibration should be checked. The blue acrylic calibration block (feeler gauge) and check/calibration procedures placard provided in the 2nd drawer of the shift supervisor’s station verified that re-calibration was required. Since the two 4-month-old AAA alkaline batteries were only providing 1.33V, new Energizer “ULTIMATE LITHIUM” batteries (which should last significantly longer) were installed before the gauge was re-calibrated. The planer’s power/energy meter showed that the planer had been used for 303.82 hours and had consumed 357.17 kWhrs of electrical energy since the meter was installed. |
Planer 20 Inch General International M29 |
In Service |
|
2,198 |
| 12/30/2024 12:39 PM |
Dallas Keck |
Testing again (form was triggering the wrong script) |
Not a Tool Repair Issue |
In Service |
Yes |
2,197 |
| 12/30/2024 12:35 PM |
Dallas Keck |
testing again |
Not a Tool Repair Issue |
In Service |
Yes |
2,196 |
| 12/30/2024 12:27 PM |
Dallas Keck |
Testing ( code updates for blast gate flag ) |
Not a Tool Repair Issue |
In Service |
Yes |
2,195 |
| 12/30/2024 08:42 AM |
Dallas Keck |
TESTING code updates for blastgate flag |
Not a Tool Repair Issue |
In Service |
Yes |
2,194 |
| 12/30/2024 08:22 AM |
Dallas Keck |
TESTING code updates (added blastgate problem flag) |
Not a Tool Repair Issue |
In Service |
Yes |
2,193 |
| 12/30/2024 08:03 AM |
Dallas Keck |
Testing shop form code updates |
Not a Tool Repair Issue |
In Service |
|
2,192 |
| 12/28/2024 12:44 PM |
Duane Kuperus |
Blast gate remains open when saw is off. Start saw and gate cycles closed and then reopens. Control box indicates “off”. Reset control box and with same result. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,191 |
| 12/28/2024 11:26 AM |
Duane Kuperus |
Check calibration of digital measure on planer |
Planer 20 Inch General International M29 |
In Service |
|
2,190 |
| 12/28/2024 11:11 AM |
Duane Kuperus |
Check system on the outside of building. Looks to be blowing dust at bottom of cyclone outside of cage. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,188 |
| 12/23/2024 08:23 PM |
Steve Carter |
Blastgate does not open |
Router Table #1 M30 |
Limited Functionality |
|
2,186 |
| 12/21/2024 09:38 PM |
Jerry Mackelburg |
The automatic blast gate needed to be re-booted. The router lift apparently needs maintenance, repair, or replacement – it’s way too hard to operate. |
Router Table #1 M30 |
Limited Functionality |
|
2,185 |
| 12/21/2024 09:35 PM |
Jerry Mackelburg |
One side or the plastic fence dust collector attachment is damaged – it should probably be replaced. The router lift apparently needs maintenance, repair, or replacement – it’s way too hard to operate. |
Router Table #2 Rockler M31 |
Limited Functionality |
|
2,184 |
| 12/21/2024 09:29 PM |
Jerry Mackelburg |
The automated blast gate is malfunctioning – it opens and closes and turns the Oneida on and off but is open when it should be closed. Re-booting did not help. |
Band Saw 14-3000 Laguna M2 |
Limited Functionality |
|
2,183 |
| 12/21/2024 09:17 PM |
Jerry Mackelburg |
The automatic blast gate was working properly this afternoon, so the note attached indicating otherwise (Rpt. No. 2183) was removed. |
Belt/Disk Sander Jet M6 |
In Service |
|
2,182 |
| 12/21/2024 09:21 AM |
Dan McNaughton |
Belt Sander (M06) the blast gate is not functional |
Sanding Station M05 |
Out of Service |
|
2,181 |
| 12/19/2024 09:49 PM |
Nels Lundgren |
Replaced the broken Starrett blade with a Timberwolf blade made of the finest swedish silicon steel! We shall see how long it lasts. Tensioned with the tension gauge. Noticed that the blade tends to track towards the back side of the tire on the upper wheel.
The broken Starrett blade appeared to fail at the weld. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,180 |
| 12/19/2024 07:17 PM |
Nels Lundgren |
A while back I saw a log from Mike M that the Makita jigsaw blade was missing. There was no blade installed in it, but the blades are right next to the charger in the stand, so I installed one. I also found 4 allen wrenches laying there and put them in the toolbox with the other mess of allen wrenches |
Power Hand Tools |
In Service |
|
2,179 |
| 12/18/2024 06:28 PM |
Jeff Bratt |
Need 1″ blue tape. What’s in the supply closet is 1 1/2″ or 2″. The dispensers on the SS console take 1″ tape. |
Supplies |
|
|
2,178 |
| 12/18/2024 06:24 PM |
Jeff Bratt |
Broken blade |
Band Saw 14-3000 Laguna M2 |
Out of Service |
|
2,177 |
| 12/14/2024 04:04 PM |
Nels Lundgren |
the router lift was reported as being hard to raise and lower. Cleaned and lubricated the router lift mechanism and it is better. There is one point in the travel that it is a little tighter, but otherwise I think it is acceptable. |
Router Table #1 M30 |
In Service |
|
2,176 |
| 12/14/2024 03:52 PM |
Nels Lundgren |
end of the paper where it is clipped in was damaged and about to break, so I replaced the drum sander paper |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,175 |
| 12/14/2024 03:33 PM |
Nels Lundgren |
Duane replaced the bandsaw blade, but the door had come off the hinges (remember the hinges are broken and requires a gentle touch). Duane left the door off and the machine out of service. I came in and reattached the door to the bandsaw. It is fine unless it is opened and it stands a chance of coming off if not handled carefully. No one should be opening the door except to change the blade. I have new hinges from laguna, but they are in the style of the hinges on the Laguna 3000 (M02) bandsaw and require drilling new attachment points for the hinges to be attached. I plan to get to this next week. |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,173 |
| 12/14/2024 02:27 PM |
Patrick Duffy |
The X stepper motor seems to not have the proper holding power and therefore may occasionally lose registration. A new controller is being ordered. |
CNC Shapeco XXL M5 |
Limited Functionality |
|
2,172 |
| 12/14/2024 01:43 PM |
Duane Kuperus |
Replaced blade in M3 Band saw. Reset blade guides and tensioned blade using EZtensioner. Saw is out of service as upper door hinges are broken. |
Band Saw 14 SE Laguna M3 |
Out of Service |
|
2,171 |
| 12/14/2024 12:52 PM |
Duane Kuperus |
Fou7nd internal dust hose disconnected. Reconnected and vacuumed internal cabinet. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,170 |
| 12/14/2024 09:10 AM |
Oi Ling Kwan |
broken blade |
Band Saw 14 SE Laguna M3 |
Out of Service |
|
2,169 |
| 12/12/2024 09:26 PM |
Nels Lundgren |
Replaced paper on drum sander |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,168 |
| 12/10/2024 05:33 PM |
Rick VanHatten |
Belt broke. Out of replacements. Rick Ordered replacements. Expect arrival on 12th. Install on the 13th. The ones we had were for the old Grizzly and not the right size |
Edge Sander Jet M15 |
Out of Service |
|
2,167 |
| 12/10/2024 02:04 PM |
Mary Russo |
Quite difficult to raise and lower bit height. Just want to make sure it is OK to keep using. |
Router Table #1 M30 |
In Service |
|
2,166 |
| 12/10/2024 10:40 AM |
Patrick Duffy |
Repaired the Sweepy Pro dust boot. The locking nut became dislodged. Don’t know why. |
CNC Shapeco HDM M4 |
In Service |
|
2,165 |
| 12/09/2024 08:30 PM |
Mike Makowski |
Shredded Belt |
Belt/Disk Sander Jet M6 |
Out of Service |
|
2,164 |
| 12/09/2024 06:17 PM |
Mike Makowski |
Makita Jig Saw – No Blade |
Power Hand Tools |
Out of Service |
|
2,163 |
| 12/09/2024 04:39 PM |
Rick VanHatten |
test |
Biscuit Jointer |
In Service |
|
2,162 |
| 12/09/2024 04:35 PM |
Bryan Blacksher |
Dust collection shroud is loose and I don’t know how to tighten it.
Care should be taken is it is used. |
CNC Shapeco HDM M4 |
Limited Functionality |
|
2,161 |
| 12/09/2024 08:30 AM |
Rick VanHatten |
Per discussion with John W. Cyclone didn’t shut off after tools were shut off. Problem seemed to be one of the router table blast gate controllers had and error. |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
2,160 |
| 12/08/2024 08:39 PM |
John Wilkinson |
The automatic dust collection system would not shut off when all power equipment was off. I called Rick Van Hatten for advisement and I was directed to place the electrical box (on the right) switch down to the “”open (off)” position and place the time delay toggle switch to “Auto.” Also, electrical box # 36, M30 Router Table #1 display reads “error.” |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,159 |
| 12/08/2024 07:16 PM |
Jerry Mackelburg |
Since performance does not appear to be significantly impacted by the apparently failing drum bearings, machine status has been changed from “Out of Service” (Rpt. No. 2155) to “Limited Functionality” for now. |
Drum Sander 25 Inch Supermax M11 |
Limited Functionality |
|
2,158 |
| 12/07/2024 07:03 PM |
Jerry Mackelburg |
The router lift problem reported int Rpt. No. 2115 was apparently fixed. |
Router Table #1 M30 |
In Service |
|
2,157 |
| 12/07/2024 06:52 PM |
Jerry Mackelburg |
Replaced leaking batteries in doorbell sensor. |
Not a Tool Repair Issue |
In Service |
|
2,155 |
| 12/07/2024 03:23 PM |
Jerry Mackelburg |
Use Placard is missing. |
Jointer 12 Inch Grizzly M16 |
Limited Functionality |
|
2,154 |
| 12/07/2024 03:17 PM |
Jerry Mackelburg |
Drum noisy when rotating – likely bad bearing(s) – 6205LU |
Drum Sander 25 Inch Supermax M11 |
Out of Service |
|
2,153 |
| 12/07/2024 11:32 AM |
Rick VanHatten |
test messge |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,152 |
| 12/05/2024 09:18 AM |
Patrick Duffy |
The white filament broke off inside its tube in the AMS. I had to remove the filament carrier to remove the broken filament. The unit is now repair and back in service.
Side issue… the plastic post on the left side of the AMS housing, which is used to receive the mounting screw for the filament carrier, is stripped. As such, it no long properly secures the carrier to the housing. It should be repaired. (Quite possible a metal insert.) Care should be taken not to ever tighten the remaining screw on the right side which in turn may cause it to be stripped, also. |
3D Printer |
In Service |
|
2,151 |
| 12/04/2024 06:30 PM |
Ron Prater |
Stop switch replaced. |
Jointer 12 Inch Grizzly M16 |
In Service |
|
2,150 |
| 12/04/2024 03:56 PM |
Jerry Mackelburg |
The doorbell works again. |
Not a Tool Repair Issue |
In Service |
|
2,149 |
| 12/04/2024 03:53 PM |
Jerry Mackelburg |
Since the Shop’s “Equipment Status” page (https://sdfwa.org/tools/) will show “Limited Functionality” or “Out of Service” for equipment reported as such until it’s reported as “In Service”, I thought it would be good to report that the Sanding Station reported as “Limited Functionality on November 9th &10th (Rpt.Nos. , was fixed (when and by who?) |
Sanding Station M05 |
In Service |
|
2,148 |
| 12/02/2024 11:28 AM |
Lou Cortellini |
student boke off knob 12 inch jointer |
Jointer 12 Inch Grizzly M16 |
Out of Service |
|
2,141 |
| 11/30/2024 08:02 PM |
Jerry Mackelburg |
The large vacuum bag was leaking today, causing the pump to run continuously (and overheating) during use. Unknown if it was “operator error” or a hardware problem, but the medium sized bag (connected in parallel) wasn’t leaking. |
Vacuum Press |
Limited Functionality |
|
2,140 |
| 11/30/2024 07:52 PM |
Jerry Mackelburg |
The doorbell isn’t working. |
Not a Tool Repair Issue |
Out of Service |
|
2,139 |
| 11/30/2024 07:52 PM |
Jerry Mackelburg |
Someone apparently re-connected the MakeSafe controller. The MakeSafe, Machine, and its automatic blast gate are now working properly (after making minor adjustments to the sanding belt tracking). IMO it would be quite useful for people who fix problems to make timely and appropriate log entries – rather than keep people guessing or surprised! 🙂 |
Disk/Belt Sander Jet M38 |
In Service |
|
2,138 |
| 11/30/2024 02:37 PM |
Jerry Mackelburg |
The MakeSafe controller has been bypassed (see previous reports). Other than that, the machine and its automatic blast gate work properly (after adjusting the sanding belt tracking). |
Belt/Disk Sander Jet M6 |
Limited Functionality |
|
2,137 |
| 11/27/2024 02:45 PM |
Doug Murphy |
Both disk belt sanders not working when plugged into the control box. Work when plugged directly into the socket. Need to manually open blast gates. |
Disk/Belt Sander Jet M38 |
Limited Functionality |
|
2,135 |
| 11/26/2024 08:25 AM |
Paul Schankin |
Damaged handwheel handle replaced. Machine in service. |
Lathe 1221 Jet M43 |
In Service |
|
2,134 |
| 11/25/2024 08:17 PM |
Lynn Welling |
Previous SS noted sander wouldn’t turn on. Make safe inop. when machine plugged directly into wall socket works fine. Ran through make safe configurations and couldn’t get it to operate. Will place OOS until reviewed. |
Belt/Disk Sander Jet M6 |
Out of Service |
|
2,133 |
| 11/16/2024 08:17 PM |
Jerry Mackelburg |
Cleaned up the ductwork between the saw and its blast gate. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,131 |
| 11/14/2024 02:49 PM |
Gordon Stone |
broken blade on MO2 Laguna 14 – blade replaced and tension set w EZtension – plz check |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,130 |
| 11/13/2024 08:45 PM |
Rick VanHatten |
Paul, test message. Please confirm you received this. |
Laser Thunder Nova 35 M18 |
In Service |
|
2,128 |
| 11/13/2024 08:44 PM |
Rick VanHatten |
Test message. Jerry, please confirm you received this |
Planer 20 Inch General International M29 |
|
|
2,127 |
| 11/13/2024 08:40 PM |
Rick VanHatten |
Test Message. Pat, please confirm you received this |
CNC Shapeco HDM M4 |
In Service |
|
2,125 |
| 11/13/2024 08:39 PM |
Rick VanHatten |
Test Message. Dana, please confirm you received this |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,124 |
| 11/13/2024 04:29 PM |
Dallas Keck |
Hi Dallas (just testing!) |
Not a Tool Repair Issue |
|
|
2,122 |
| 11/12/2024 08:34 AM |
Paul Schankin |
Drained approx 1/4 cup of water out of holding tank, machine in service. |
Air Compressor Fortress |
In Service |
|
2,121 |
| 11/11/2024 02:24 PM |
Bryan Blacksher |
The router bit (marked with blue tape), that resides in the silver box in the bottom of the Router #1 (M30) table, has a bearing that is too small for the router bit. The outside of the bearing should be even with the outer edge of the bit. As it is, the bit leaves an edge on the wood that is being shaped. |
Not a Tool Repair Issue |
In Service |
|
2,119 |
| 11/11/2024 01:21 PM |
Jerry Mackelburg |
The hinges on the upper door are problematic and very close to failure – which would put the saw out of service. Hinges like these (https://www.mcmaster.com/1635A102/) should be good, inexpensive, and easy replacements. |
Band Saw 14 SE Laguna M3 |
Limited Functionality |
|
2,118 |
| 11/11/2024 01:04 PM |
Bryan Blacksher |
The router bit cabinet was unlocked when I came in today. Just FYI. |
Not a Tool Repair Issue |
|
|
2,117 |
| 11/10/2024 04:24 PM |
Jerry Mackelburg |
The router lift runs requires more effort and doesn’t operate as smoothly as it should. Cleaning and spray dry lubing the leadscrew and guide rails help some – but! |
Router Table #1 M30 |
Limited Functionality |
|
2,115 |
| 11/10/2024 04:18 PM |
Jerry Mackelburg |
The Festool dust extractor has to be manually turned on (the current sensor required for automatic starting/stopping isn’t working.) |
Sanding Station M05 |
Limited Functionality |
|
2,114 |
| 11/10/2024 03:22 PM |
Jerry Mackelburg |
Bryan Harding reportedly replaced the broken blade on Nov. 9, 2024 a 6:35pm (maybe he should be given access for shop log entries?) |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,113 |
| 11/10/2024 08:53 AM |
Rick VanHatten |
Removed chuck |
Lathe 1221 Jet M43 |
In Service |
|
2,111 |
| 11/10/2024 08:48 AM |
Rick VanHatten |
Removed spindle with pipe wrench. Cleaned up jaw marks on lathe. Ordered replacement spindle. Its a significant tear down to replace. Will wait until January to do |
Spindle Sander Enlon M33 |
In Service |
|
2,108 |
| 11/09/2024 03:03 PM |
Mark Umphres |
trend sharpening plate and bench dogs missing from the locations indicated in the tool database. |
Not a Tool Repair Issue |
|
|
2,107 |
| 11/09/2024 02:38 PM |
Mark Umphres |
broken blade |
Band Saw 14 SE Laguna M3 |
Out of Service |
|
2,106 |
| 11/09/2024 01:42 PM |
Paul Schankin |
3D printer extruder clog removed, machine in service. |
3D Printer |
In Service |
|
2,105 |
| 11/09/2024 12:13 PM |
Nancy Bosecker |
This is probably me being ignorant, but the Festool vaccuum on the sanding station did not turn off when the sanders were off. The switch is on ‘Manual On’. So, I turned it off manually and probably now the whole thing is wrong. Sorry. |
Sanding Station M05 |
In Service |
|
2,104 |
| 11/09/2024 12:05 PM |
Nancy Bosecker |
Can someone order the thinner roles of blue tape for the caddies? We have plenty of extra wide tape but not enough thinner one. |
Supplies |
|
|
2,103 |
| 11/09/2024 11:26 AM |
Nancy Bosecker |
The miter saw is really squeaky and could use some WD-40. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,102 |
| 11/08/2024 01:52 PM |
Dallas Keck |
test |
Not a Tool Repair Issue |
|
|
2,101 |
| 11/07/2024 04:32 PM |
Duane Kuperus |
Vacuumed saw internals. Cleaned and lubed Blade Elevation and Tilt mechanisms. Replaced blade and maked removed blade for cleaning. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,100 |
| 11/07/2024 02:39 PM |
Lou Cortellini |
Update from previous entry: found circuit breaker in off position. Reset CB and tools now have power. |
Not a Tool Repair Issue |
In Service |
|
2,098 |
| 11/07/2024 02:03 PM |
Lou Cortellini |
Electric outlets on shop wall behind router table and belt/disc sander are not getting power. Checked router table with extension cord as a work around. |
Not a Tool Repair Issue |
Limited Functionality |
|
2,097 |
| 11/06/2024 10:50 AM |
Paul Schankin |
Clogged extruder, out of service. |
3D Printer |
Out of Service |
|
2,096 |
| 11/02/2024 01:35 PM |
Duane Kuperus |
Blast gate on MO@ Laguna did not open automatically when saw was energized.[ Reset controller and now works. Blast gate makes noise as it has an alignment issue when opening. Needs alignment check. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,095 |
| 10/31/2024 11:24 AM |
Mike Makowski |
Stop Button on Router 1 is broken, but still attached |
Router Table #1 M30 |
In Service |
|
2,094 |
| 10/30/2024 06:20 PM |
Ron Prater |
Operation doesn’t trigger the dust collector system. |
Band Saw 14 SE Laguna M3 |
Limited Functionality |
|
2,093 |
| 10/30/2024 02:49 PM |
Doug Murphy |
Pindle stuck in machine. Can’t change. |
Spindle Sander Enlon M33 |
Limited Functionality |
|
2,092 |
| 10/28/2024 06:21 PM |
Mike Makowski |
Blue Board Calipers missing |
Not a Tool Repair Issue |
|
|
2,091 |
| 10/28/2024 03:55 PM |
Bryan Blacksher |
Need new, readable, “Arm” and “Disarm” labels on the Ring security control panel. The current labels are really hard to read, especially in the dark. |
Not a Tool Repair Issue |
In Service |
|
2,090 |
| 10/28/2024 10:56 AM |
Jerry Mackelburg |
As of Sunday afternoon, the leftmost shade in the classroom was (is?) still too wide to allow the Northeast window panel to be properly closed. |
Not a Tool Repair Issue |
Limited Functionality |
|
2,089 |
| 10/26/2024 08:20 PM |
Jerry Mackelburg |
Since automated blast gates recently replaced the manual ones on several more machines, the “Manual Blast Gate” notes were removed from those machines. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,088 |
| 10/26/2024 08:10 PM |
Jerry Mackelburg |
The duck work from the blast gate to the saw was reconfigured to improve blast gate reliability and operation. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,087 |
| 10/24/2024 10:26 PM |
Nels Lundgren |
Blast Gate stuck in closed position. Error indicator on the electronics. Rebooted multiple times, but it was REALLY stuck. I had to loosen the blots that hold the blast gate sandwich together to free it. Once I did that, I reconnected it and retightened the bolts on the blast gate. Cycled multiple times and is working. Don’t know what was holding it closed so tightly. In general the plastic gates don’t slide very smoothly. Maybe it was an accumulation of sawdust?? |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,085 |
| 10/22/2024 04:35 PM |
Duane Kuperus |
Table saw #2 blade elevation hand-wheel was reported as loose. Inspection shoes set scre in hand-wheel was not tight. Keyway was in place. Tightened setscrew and all good. Returned to full service. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,084 |
| 10/21/2024 06:22 PM |
Steve Carter |
Height adjustment wheel came loose, I was able to put it back on but could come off again. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,083 |
| 10/20/2024 08:35 PM |
Nels Lundgren |
Can’t find the Wixie gauge |
Not a Tool Repair Issue |
Out of Service |
|
2,082 |
| 10/17/2024 04:09 PM |
Nels Lundgren |
Rick and I got the stuck spindle out, using a pipe wrench. We think a piece of metal got down in the arbor. The spindles need their threads cleaned up with a die and the sander needs its threads cleaned up with a tap. It is important to only tighten hand tight, using one wrench to hold the arbor. If needed use the second wrench to remove the spindle. Rick took the spindle that we removed home to clean up the scars from the pipe wrench |
Spindle Sander Enlon M33 |
In Service |
|
2,081 |
| 10/17/2024 11:06 AM |
Nels Lundgren |
Blade Guard Mechanism not moving smoothly. Lubed the blade guard mechanism and is operating more smoothly. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,080 |
| 10/17/2024 11:04 AM |
Nels Lundgren |
Replaced Blade on M03 Bandsaw and tensioned with the tensioning gauge. More blades are on order. |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,079 |
| 10/16/2024 02:37 PM |
Doug Murphy |
Can’t change spindles, threads locked. Need bigger wrench |
Spindle Sander Enlon M33 |
Limited Functionality |
|
2,078 |
| 10/14/2024 02:31 PM |
Bryan Blacksher |
Bandsaw blade broke. I have removed the broken blade. Needs a new blade. |
Band Saw 14 SE Laguna M3 |
Out of Service |
|
2,077 |
| 10/14/2024 12:54 PM |
Jerry Mackelburg |
Cleaned debris out of the router’s electronics and removed a wood chip that was preventing the speed control switch from fully slowing down the router. Checked the brushes. |
Router Table #1 M30 |
In Service |
|
2,076 |
| 10/14/2024 12:50 PM |
Jerry Mackelburg |
Cleaned debris out of the router’s electronics, checked the brushes, cleaned and dry-lubed the lift’s lead screw and guide rails, also moved the router up in the lift to maximize its utility with long router bits. |
Router Table #2 Rockler M31 |
|
|
2,075 |
| 10/14/2024 12:38 PM |
Jerry Mackelburg |
Cleaned debris from lower blade guide and lower cabinet. Adjusted MAKESAFE braking torque to stop blade more quickly. |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,074 |
| 10/12/2024 08:00 PM |
Jerry Mackelburg |
Cleaned blade guides and mounts, replaced blade, adjusted blade tension and guides. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,073 |
| 10/09/2024 01:46 PM |
John Goodrich |
blade broke |
Band Saw 14-3000 Laguna M2 |
Out of Service |
|
2,072 |
| 10/07/2024 02:46 PM |
Bryan Blacksher |
The drive V-Belt is broken. Needs to be replaced. |
Band Saw 14-3000 Laguna M2 |
Out of Service |
|
2,071 |
| 10/07/2024 02:01 PM |
Bryan Blacksher |
The drawer holding the hand sanders (middle drawer, right side) is very wobbly. I believe that one or more screws are loose in the drawer glides. |
Sanding Station M05 |
In Service |
|
2,070 |
| 10/05/2024 02:10 PM |
Mark Umphres |
limit switch broken. Dust Collection is activated randomly when the gate is closed. |
Edge Sander Jet M15 |
In Service |
|
2,069 |
| 10/05/2024 11:53 AM |
Duane Kuperus |
All working fine now. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,068 |
| 10/04/2024 08:35 PM |
Jerry Mackelburg |
Re. Rpt No. 2068, the caliper’s battery was apparently changed so the caliper could be returned to service sometime before this afternoon. |
Planer 20 Inch General International M29 |
In Service |
|
2,067 |
| 10/03/2024 11:26 AM |
Lynn Welling |
caliper for planer wont zero or change from mm to in. pulled and put on ss desk |
Planer 20 Inch General International M29 |
In Service |
|
2,066 |
| 10/02/2024 06:52 PM |
Rick VanHatten |
Test |
Not a Tool Repair Issue |
In Service |
|
2,065 |
| 10/02/2024 04:26 PM |
Rick VanHatten |
Using gentle persuasion, removed tail stock |
Lathe 1221 Jet M43 |
In Service |
|
2,064 |
| 10/02/2024 03:37 PM |
Doug Murphy |
Auto blast gate not functional. |
Band Saw 14 SE Laguna M3 |
Limited Functionality |
|
2,063 |
| 10/01/2024 04:58 PM |
Jerry Mackelburg |
Additional usage signage has been added to hopefully eliminate/minimize users screwing up the Wixey gauge’s absolute (“ABS”) accuracy reading by holding the “ON/OFF” button in long enough (3-5 seconds) to cause improper re-calibration. Proper calibration procedures have been added to the back of the planer’s hanging Wixey placard for shift supervisor use if he/she determines it’s necessary. A calibration test block has been provided for their use in that determination. |
Planer 20 Inch General International M29 |
In Service |
|
2,062 |
| 10/01/2024 04:52 PM |
Jerry Mackelburg |
Usage instructions for the auxiliary table and sacrificial fence stop blocks were added to the back of the fence adjustment procedure placard in the saw’s adjacent accessory drawer.
Re. Rpt.No. 2,019, the sawblade had been replaced and the “large allen wrench left behind fence and member accidently struck wrench while crosscutting” (likely the “hex wrench” used for blade removal/installation) had been returned to its normal stowage location at the near end of the lower “slide pole”. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
2,061 |
| 10/01/2024 04:27 PM |
Jerry Mackelburg |
Re. Rpt.No. 2,057, Dallas optimized (and marked) the position of the blast gate’s current sensor on the saw’s power drop. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,060 |
| 10/01/2024 04:22 PM |
Jerry Mackelburg |
Re. Rpt.No. 2,055, The calipers have been replaced on the 20″ planer and tool-wall. |
Not a Tool Repair Issue |
In Service |
|
2,059 |
| 09/30/2024 07:18 PM |
Mike Makowski |
Out of CA glue |
CNC Shapeco HDM M4 |
In Service |
|
2,057 |
| 09/28/2024 08:23 PM |
Jerry Mackelburg |
The current sensor needed to be rotated on the power drop to keep the gate open (and the Oneida on) while the saw was running. Limited functionality because of the uncertainty in its proper placement. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
Limited Functionality |
|
2,055 |
| 09/28/2024 08:00 PM |
Jerry Mackelburg |
Calipers are missing from 20-inch planer and tool-wall |
Not a Tool Repair Issue |
Limited Functionality |
|
2,053 |
| 09/26/2024 04:20 PM |
Mary Russo |
Slow Speed Grinder in Lathe Area only one bolt is holding it down. 2nd Bolt is lose and does not seem to fit into the hole that it should line up with. I re3placed the right side slide. The old one was not grabbing the bar very well. |
Not a Tool Repair Issue |
In Service |
|
2,052 |
| 09/21/2024 09:57 AM |
Skip Florey |
Saw blade broke. Replaced the blade and it is in service. |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,049 |
| 09/21/2024 08:32 AM |
Paul Schankin |
Drained approx 1/4 cup of water out of air tank. Machine in service. |
Air Compressor Fortress |
In Service |
|
2,048 |
| 09/17/2024 07:54 PM |
Nels Lundgren |
Replenished the 100,120,150,180 grit sandpaper |
Supplies |
In Service |
|
2,047 |
| 09/17/2024 11:47 AM |
Paul Schankin |
Descaled Kuerig coffee maker. |
Not a Tool Repair Issue |
In Service |
|
2,046 |
| 09/16/2024 04:06 PM |
Mike Makowski |
Pad lock missing from gated wood area |
Not a Tool Repair Issue |
|
|
2,045 |
| 09/16/2024 03:58 PM |
Mike Makowski |
Fingerboard tools missing from Table1 2A |
Not a Tool Repair Issue |
|
|
2,044 |
| 09/16/2024 12:44 PM |
Nels Lundgren |
Replaced the Velcro pads on two orbital sanders.
Need more hoses and adapters for the sanders to the sanding station. Only have three. |
Sanding Station M05 |
In Service |
|
2,043 |
| 09/14/2024 01:05 PM |
Nancy Bosecker |
We’re low on full sheets of sandpaper for grits 100, 120, 150, 180. I just sold one of each. |
Supplies |
|
|
2,042 |
| 09/14/2024 12:16 PM |
Nancy Bosecker |
Dave Sloat noted that the spring for the safety guard of the jointer could be tightened, as it does not snap back without manual intervention after jointing. |
Jointer 12 Inch Grizzly M16 |
In Service |
|
2,041 |
| 09/04/2024 11:54 AM |
Paul Schankin |
Installed automated blast gate and activation of shop DC. Machine in service. |
CNC Shapeco XXL M5 |
In Service |
|
2,040 |
| 09/04/2024 11:53 AM |
Paul Schankin |
Installed automated blast gate and activation of shop DC. Machine in service. |
CNC Shapeco HDM M4 |
In Service |
|
2,039 |
| 09/04/2024 11:52 AM |
Paul Schankin |
Dust collection bag full. Replaced bag, machine in service. Last bag replaced 6/20/2024. |
Shop Vac Craftsman |
In Service |
|
2,038 |
| 09/02/2024 07:51 PM |
Mike Makowski |
Broken Blade; Replace by Brian Lieb |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,037 |
| 08/31/2024 08:28 PM |
Jerry Mackelburg |
Oiled table roller bushings. Cleaned and waxed tables and table rollers. |
Planer 20 Inch General International M29 |
In Service |
|
2,036 |
| 08/31/2024 08:17 PM |
Jerry Mackelburg |
The supervisor station’s CCTV display wasn’t working for the 2:00 PM shop shift. The operating instructions apparently don’t reflect the current (Google?) system (maybe I should have checked the “What’s New” list?!) Since the shop’s display computer apparently was having difficulty “connecting to the server”, I opened the server’s(?) bench room cabinet door and tried to cool things down with a fan – that didn’t seem to help. Maybe those doors should be removed and the operating instructions updated? |
Not a Tool Repair Issue |
Out of Service |
|
2,034 |
| 08/28/2024 08:30 AM |
Paul Schankin |
For record only. When Oneida moved outside, lubed the grease fittings on upper and lower motor bearings with applicable grease, approx 1-2 teaspoons each. Manual suggests every 2,000 hours that lubing occurs. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
2,033 |
| 08/25/2024 05:27 PM |
Jerry Mackelburg |
The Wixey reading was off again today (by 0.12″ – about 10 times what’s expected.) The 1.5V AAA Alkaline batteries both measured 1.32V. Maybe that’s not enough to maintain calibration. So, they were replaced with fresh Alkalines and the gauge was re-calibrated. |
Planer 20 Inch General International M29 |
In Service |
|
2,031 |
| 08/25/2024 04:14 PM |
Jerry Mackelburg |
The sliding window panels in the rightmost North facing window were switched to enable them to work properly. The right panel is still prevented from closing fully by the adjacent window shade. |
Not a Tool Repair Issue |
Limited Functionality |
|
2,030 |
| 08/23/2024 11:50 AM |
Jerry Mackelburg |
Re-calibrated the Wixey thickness gauge (someone had apparently held “ON/OFF” in for more than 3 seconds to mess it up). |
Planer 20 Inch General International M29 |
In Service |
|
2,029 |
| 08/22/2024 02:37 PM |
Gordon Stone |
remote thickness read out may need recalibration |
Planer 20 Inch General International M29 |
In Service |
|
2,028 |
| 08/15/2024 09:23 PM |
Nels Lundgren |
Automatic Blast Gate inop. Blast gate opens but continues to open until it reaches the end of its travel and then chatters away trying to go further. Disconnected Blast Gate for manual operation and unplugged the controller. |
Band Saw 14 SE Laguna M3 |
Limited Functionality |
|
2,026 |
| 08/13/2024 09:54 AM |
Paul Schankin |
Dust collection bag full, replaced DC bag. Machine in service. |
Sanding Station M05 |
In Service |
|
2,025 |
| 08/13/2024 09:52 AM |
Paul Schankin |
Filter clogged, dust collection bag missing. Cleaned filter, installed DC bag, machine in service. |
Shop Vac Rigid |
In Service |
|
2,024 |
| 08/13/2024 09:49 AM |
Paul Schankin |
Replaced dust collection bag. Machine in service. |
Dust Extractor Bosch |
In Service |
|
2,022 |
| 08/13/2024 09:48 AM |
Paul Schankin |
Replaced dust collection bag. Machine in service. |
Shop Vac Rigid |
In Service |
|
2,021 |
| 08/12/2024 08:21 PM |
Steve Carter |
Router table small part holder base plate, a section was routed away. Will Wehner was the member using it at the time |
Not a Tool Repair Issue |
In Service |
|
2,020 |
| 08/12/2024 06:44 PM |
Steve Carter |
blast gate displays error and will not open |
Band Saw 14-3000 Laguna M2 |
Limited Functionality |
|
2,019 |
| 08/12/2024 06:42 PM |
Phil Silverstone |
Large allen wrench left behind fence and member accidently hit wrench while crosscutting. Wrench flew out but no one injured. Blade appears to be intact but would check integrity and alignment. |
Miter Saw 12 Inch Makita M26 |
Out of Service |
|
2,018 |
| 08/12/2024 04:24 PM |
Phil Silverstone |
Large allen wrench left behind fence and member accidently struck wrench while crosscutting. No one injured but not sure of blade integrity and alignment. |
Miter Saw 12 Inch Makita M26 |
Out of Service |
|
2,017 |
| 08/11/2024 02:08 PM |
Duane Kuperus |
On Saturday, Lou Cortellini and checked and adjusted tension on the Motor Drive belt for the #2 Table Saw per the instructions. New belts (motor and arbor) were installed last week. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,016 |
| 08/11/2024 12:22 PM |
Nels Lundgren |
Blast gate for Drum Sander M10 cycling between open and closed when not in use. Tried rebooting the controller by disconnecting and reconnecting power, but same results. Left power disconnected and posted a sign to operate manually. |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
2,015 |
| 08/05/2024 06:50 PM |
Mike Makowski |
Hex screw with spacer and nut found on floor next to Resaw. |
Not a Tool Repair Issue |
In Service |
|
2,013 |
| 08/04/2024 05:51 PM |
Jerry Mackelburg |
Yesterday, assuming that it was the right thing to do (was it?), I opened the shades and windows in the upstairs classroom. |
Not a Tool Repair Issue |
In Service |
|
2,012 |
| 08/04/2024 05:34 PM |
Jerry Mackelburg |
Yesterday removed buildup (including nasty uncured epoxy?) from cutters, cutterhead, cutterhead casting, chip deflectors, all rollers, and tables. Cleaned all and applied BOESHIELD T-9 to table rollers and tables. Verified Wixey thickness gauge calibration. |
Planer 20 Inch General International M29 |
In Service |
|
2,010 |
| 08/03/2024 08:50 PM |
Nels Lundgren |
yesterday (Friday), the blade broke during class. Student was making a straight cut in Sapele. Replaced blade and tensioned using the tension gauge |
Band Saw 14-3000 Laguna M2 |
In Service |
|
2,009 |
| 08/03/2024 02:49 PM |
Duane Kuperus |
On 8/2 Lou Courtellini and I vacuumed the cabinet interior and replaced the motor and arbor belts on the #2 table saw |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,007 |
| 08/03/2024 10:58 AM |
Jerry Mackelburg |
The Shop Log seems to be empty! |
Not a Tool Repair Issue |
Out of Service |
|
2,006 |
| 08/01/2024 09:54 PM |
Nels Lundgren |
Replaced paper. Had a black buildup streak down the middle |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
2,004 |
| 08/01/2024 09:36 PM |
Nels Lundgren |
Table Saw 2 top was pretty gunky and has rust showing. I cleaned the gunk with some acetone. The top needs a good polish. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,003 |
| 07/29/2024 06:48 AM |
Nels Lundgren |
Bandsaw blade broke while student was making routine outside corner cut on cutting board. Earlier I had noted that the cut was rough. Replaced the blade and tensioned using the tension gauge. |
Band Saw 14 SE Laguna M3 |
In Service |
|
2,002 |
| 07/27/2024 02:03 PM |
Dana Chapin |
Dust collection gate does not have a delay when turning off the saw |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
2,001 |
| 07/24/2024 06:21 PM |
Jeff Bratt |
Actually, I was able to adjust the micro-switch so it works OK now. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
1,999 |
| 07/24/2024 05:38 PM |
Jeff Bratt |
The manual blast gate for the Robusr lathe is flaky. It doesn’t reliably go to Open state when the gate is pulled out. By fiddling with the micro-switch I can get the light to go on, and it will stay on, but it’s unreliable. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
1,998 |
| 07/20/2024 03:02 PM |
Jerry Mackelburg |
Need more 5X30 Dominos (sold 40 today) |
Supplies |
Limited Functionality |
|
1,997 |
| 07/19/2024 06:30 PM |
Jerry Mackelburg |
Recalibrated the Wixey thickness gauge/DRO. It’s likely that someone held the ON/OFF button too long (which messed it up). |
Planer 20 Inch General International M29 |
In Service |
|
1,994 |
| 07/19/2024 03:46 PM |
Patrick Duffy |
Mini PC had a system failure. “Unable to communicate with hard drive.” Replaced the defective PC with a new BOSGAME PC. All applications have been loaded and are functioning properly.
User data files have not been moved into the new computer.
NOTE: Carbide Create has been revised on this PC to build 635. — Did not update the HDM at this time. |
CNC Shapeco XXL M5 |
In Service |
|
1,993 |
| 07/18/2024 08:12 PM |
Scott Baldwin |
Digital read out does not seem to be accurate |
Planer 20 Inch General International M29 |
In Service |
|
1,991 |
| 07/15/2024 08:40 PM |
Steve Carter |
Tail stock is missing a set screw, and jacobs chuck is stuck in tail stock |
Lathe 1221 Jet M43 |
Limited Functionality |
|
1,990 |
| 07/10/2024 11:08 AM |
Rick VanHatten |
Out feed table adjusted so its below the table saw surface level. This is was done by tightening up the bolt on the left side the outfeed table that attaches it to the table saw. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
1,988 |
| 07/10/2024 11:06 AM |
Rick VanHatten |
Replaced conveyor belt and adjusted outfeed table as much as possible. It still runs a little below the conveyor belt. If its a longer piece need to support by hand or use the rollers |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
1,987 |
| 07/10/2024 11:01 AM |
Jerry Mackelburg |
Jerry checked out the planer and found sharpness and cut good. Not quite as good as the new Powermatic, but good. |
Planer 20 Inch General International M29 |
In Service |
|
1,986 |
| 07/08/2024 02:04 PM |
Bryan Blacksher |
Yellow Magnetic Featherboard – The knob on one end works but the knob on the other end just spins and does not engage the catch to metal. Needs service or replacement. |
Not a Tool Repair Issue |
Limited Functionality |
|
1,985 |
| 07/08/2024 01:51 PM |
Bryan Blacksher |
Based on the sound being made while planing, it would appear that the blades are dull. |
Planer 20 Inch General International M29 |
In Service |
|
1,984 |
| 07/06/2024 01:56 PM |
Dana Chapin |
outfeed table significantly below belt. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
1,983 |
| 07/06/2024 09:19 AM |
Wesly Berneberg |
Changed blade on saw. Previous blade in drawer 13C with today’s date (7/6) |
Band Saw 14-3000 Laguna M2 |
In Service |
|
1,982 |
| 07/03/2024 04:31 PM |
Rick VanHatten |
Backsaw handle repaired |
Hand Tools |
In Service |
|
1,981 |
| 07/03/2024 04:31 PM |
Rick VanHatten |
Bench Room window shade fixed |
Not a Tool Repair Issue |
In Service |
|
1,980 |
| 07/02/2024 03:52 PM |
Nels Lundgren |
he Outfeed table for TS #2 is slightly higher than the table saw, so it can cause a “catch” when the end of the piece moves onto the outfeed table. The outfeed table is flat on the ground and the saw height is not adjustable to my knowledge. It is only about 1/32″, so I think planing the edge of the outfeed table will do the trick. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
1,979 |
| 06/29/2024 04:33 PM |
Duane Kuperus |
Checked table saw fence set up on #2 saw and found it a bit out of parallel with Miter slot. Adjusted to parallel. |
Table Saw 10 Inch #2 Sawstop Industrial M39 |
In Service |
|
1,978 |
| 06/29/2024 12:56 PM |
Nels Lundgren |
The Miter saw got alot of work this afternoon. During an operation, Nancy noticed the blade guard did not retract, and discovered a bolt that holds the bottom of the lever that raises and lowers the blade guard had come all the way off. Reinstalled the bolt and all is good.
Maybe a good idea to have a preventative maintenance schedule, to check the bolts on the saw. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
1,977 |
| 06/28/2024 03:51 PM |
Paul Schankin |
Head collision (who and day unknown) resulted in laser beam alignment issues. Adjusted #3 mirror, checked vertical alignment bed to focus block, more detailed report on Nova 35 PC. Machine in service. |
Laser Thunder Nova 35 M18 |
In Service |
|
1,976 |
| 06/26/2024 06:58 PM |
Mike Makowski |
One dead pigeon found (by the sanders) and disposed of. |
Not a Tool Repair Issue |
|
|
1,974 |
| 06/26/2024 06:33 PM |
Mike Makowski |
Unable to close upstairs corner window in classroom as it is blocked by the end of the shade |
Not a Tool Repair Issue |
|
|
1,973 |
| 06/23/2024 01:48 PM |
Jerry Mackelburg |
Very few sleeves for laminator are left. |
Supplies |
In Service |
|
1,972 |
| 06/22/2024 03:21 PM |
Jerry Mackelburg |
Cutoff buildup under the kerf plates was removed and the sliding fences were trimmed. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
1,971 |
| 06/22/2024 03:15 PM |
Jerry Mackelburg |
The infrared drum fill level sensor wasn’t working (red light wouldn’t flash with its lens covered). The sensitivity was increased to get it to work, but it will probably need to be re-adjusted when there is something in the drum. |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
1,970 |
| 06/22/2024 01:33 PM |
Duane Kuperus |
need new small spindle sanding sleeves. Less than 3/4 inch. |
Spindle Sander Enlon M33 |
In Service |
|
1,969 |
| 06/22/2024 01:29 PM |
Nels Lundgren |
Need new conveyor belt. The conveyor belt is worn on the right side, causing the piece to either get stuck in the sander or possibly ejecting it backwards out the front of the sander where the operator may be standing. I put a note on the sander in blue tape.
This is caused by the sander dialed down to minimum height above the conveyor and the dust collection suction, drawing the belt up into the drum sander. |
Drum Sander 25 Inch Supermax M11 |
Limited Functionality |
|
1,968 |
| 06/22/2024 01:25 PM |
Nels Lundgren |
replaced the drum sander paper. The old paper had been gummed up on both ends and worn in the middle. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
1,967 |
| 06/21/2024 10:31 PM |
Nels Lundgren |
Bandsaw blade broke while IWW A student was making a routine cut. Don’t believe he was exerting undue sideways pressure on the blade. The broken blade struck his finger resulting in a small cut, but it was a bleeder. Cleaned it up and applied a bandaid and continued with class. Re[placed the blade and tensioned with the tension gauge. I noticed that the tension indicator at the top was lower than the sharpie mark for 1/4″ blade. Perhaps the blade was under tensioned which led to the blade breaking? When tensioned with the tension gauge the tension indicator at the top is higher than the sharpie mark for 1/4″ blade. I left it as tensioned with the tension gauge.
The hinges to the upper door are broken. When I opened the door it damn near fell off. The top hinge is broken and barely holding together, and the door came out of the bottom hinge. I put the bottom hinge back together and shut the door and it is holding. I put a note on the bandsaw to use caution when opening the door.
I think we ought to look at the guides on these bandsaws and evaluate them for adjustment. seems like they travel a little too far backwards before touching the back of the guide. |
Band Saw 14 SE Laguna M3 |
In Service |
|
1,966 |
| 06/21/2024 10:21 PM |
Nels Lundgren |
Bandsaw blade broke at the end of an IWW A class. TA (Bill Bloomberg) reported that he barely touched the blade with a piece of wood and it broke. It had been used for the past hour in class. Replaced the blade and tensioned using the tension guide. |
Band Saw 14-3000 Laguna M2 |
In Service |
|
1,965 |
| 06/17/2024 01:46 PM |
Patrick Duffy |
1. The monitor mas been replace with a 24″ monitor.
2. VCarve Pro Makerspace Edition V11.0xx and V11.55x have been removed from the system.
3. Carbide Create has bee upgraded to V 757. |
CNC Shapeco XXL M5 |
In Service |
|
1,963 |
| 06/17/2024 01:45 PM |
Patrick Duffy |
1. The monitor mas been replace with a 24″ monitor.
2. VCarve Pro Makerspace Edition V11.0xx and V11.55x have been removed from the system.
3. Carbide Create has bee upgraded to V 757.
|
CNC Shapeco HDM M4 |
In Service |
|
1,962 |
| 06/14/2024 12:06 PM |
Tom York |
The left side window shade in the bench room will bot close. Nels and I checked, it carefully and can’t determine the cause. |
Not a Tool Repair Issue |
Limited Functionality |
|
1,961 |
| 06/13/2024 10:36 AM |
Lynn Welling |
drawstring on blind in upstairs classroom came off upper roller. I was unable to repair. |
Not a Tool Repair Issue |
In Service |
|
1,960 |
| 06/13/2024 10:23 AM |
Nels Lundgren |
Resupplied the 400 grit sandpaper |
Supplies |
In Service |
|
1,959 |
| 06/10/2024 01:38 PM |
Bryan Blacksher |
The belt has a 1″ x 2″ piece missing from the middle (height-wise) of the belt. The machine can still be used for edge sanding of thinner pieces. Not sure how the belt would react to taller pieces. |
Edge Sander Jet M15 |
In Service |
|
1,958 |
| 06/09/2024 01:36 PM |
Jerry Mackelburg |
The nuts on the sliding fences’ T-Bolts have been replaced with knobs to enable tool-less fence adjustment. So, the nut driver has been removed from the adjacent saw accessory drawer. The angular misalignment of the T-Track on the left (and right?) extension table with the saw’s fences caused some user confusion yesterday. The Makita material vertical vise/clamp appears too worn to restore its proper automatic quick release/clamp function. It should probably be replaced. |
Miter Saw 12 Inch Makita M26 |
Limited Functionality |
|
1,957 |
| 06/09/2024 01:15 PM |
Jerry Mackelburg |
There’s a substantial time delay before open blast gates can turn the unit back on after it turns off.
Yesterday at 2:00PM the automatic time delay had been set to “Short” rather than “Long” as has been advised (to minimize motor stress/heating). Maybe monitoring the motor temperature would be prudent, especially after the unit is moved outside? That motor’s name plate should show what it’s rated for as well as its manufacturer (“Baldor”?) and model number (to get additional usage and maintenance guidance). It’s likely that the motor/system would perform significantly better for longer if the motor was provided with 230V rather than the current 206V.
Also, at the end of yesterday’s 2:00-5:00 PM shift, sawdust/chips had backed up in the leftmost dust drum’s hose (fortunately the rightmost drum was only ~2/3 full!). I didn’t notice if the red alarm light was on or not (and didn’t think to check it either before or after wiping off its lens when emptying the drums). (The video should show if it was working.) Maybe an audio alarm and/or an additional more dependable (electro-mechanical?) sensor system should be considered? |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
1,956 |
| 06/04/2024 02:11 PM |
Tom Roetker |
Disassembled drive box . Tightened the ground lug and reinserted all motor connectors. Looked at belt motor brushes but did not fully disassemble. belt drive motor working now. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
1,955 |
| 06/03/2024 08:22 PM |
Steve Carter |
feed belt not moving |
Drum Sander 25 Inch Supermax M11 |
Out of Service |
|
1,954 |
| 06/02/2024 07:48 PM |
Tom Roetker |
the light on the blast gate works intermittently. doesn’t limit use |
Router Table #2 Rockler M31 |
In Service |
|
1,953 |
| 06/02/2024 05:13 PM |
Jerry Mackelburg |
Thin strips and debris that was again building up under the kerf plate was removed. Laminated Instructions on how to easily and properly adjust the sliding fences was added to the drawer adjacent to the saw. That drawer now also contains a nut-driver to facilitate fence adjustment, a labeled Stop Block for that fence, and the saw’s operator manual. An additional (Bosch) easy-to-use quick release vertical vise was installed/placed in the left hole on the saw’s base. Signage was added to the saw’s original (Makita) vise to assist in its proper use. It was installed/placed in the base’s right vise hole. Its adjustability and potential for lower profiles makes it a better option for bevel cuts. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
1,952 |
| 05/29/2024 04:14 PM |
Nels Lundgren |
Restocked gloves in Assembly Table #2, drawer 3C with gloves M and L from back storage room. Will get more gloves M, L, XL from Harbor Freight to restock the storage room. |
Supplies |
In Service |
|
1,951 |
| 05/29/2024 02:38 PM |
Patrick Duffy |
Laptop will not connect to the 3D Printer via Bambu Studio. NOTE: the new Digital Tools laptop can be used until this problem is resolved. The apparent problem seems to be in the printer setup withing Bambu Studio in the 3D printer laptop. |
3D Printer |
In Service |
|
1,949 |
| 05/29/2024 02:27 PM |
Doug Murphy |
Shop out of disposable gloves. |
Supplies |
In Service |
|
1,948 |
| 05/23/2024 03:03 PM |
Gordon Stone |
2″ x 3/4″ hole in Jet Edge Sander belt |
Edge Sander Jet M15 |
In Service |
|
1,947 |
| 05/20/2024 01:17 PM |
Jerry Mackelburg |
The Shop Log’s filtering feature, which could be very useful for identifying and correcting problems, still does not work for all currently active machines. Removing (after archiving) entries from now inactive machines would also be helpful, as would adding a column to show machine status (“In Service, Limited Functionaliy, Out of Service”). |
Not a Tool Repair Issue |
Limited Functionality |
|
1,946 |
| 05/19/2024 10:16 PM |
Jerry Mackelburg |
2.5-inch-high sliding “zero” clearance Baltic Birch vertical fences were installed. (The deep socket wrench/screwdriver currently required to loosen/tighten them is in the adjacent “Miter Accessories & Tools Drawer” along with a Stop Block and another vertical vise/clamp.) Placards with usage instructions for the saw were hung from hooks attached to the left and right sides of the saw’s enclosure. Note that shop policy is now that slide “Push” cutting should only be used when necessary (because of the width of the workpiece) and that the slide mechanism must be disabled when it’s not being used (to avoid kickback). |
Miter Saw 12 Inch Makita M26 |
In Service |
|
1,945 |
| 05/19/2024 09:39 PM |
Jerry Mackelburg |
A placard with usage instructions for the Wixey WR550 planer thickness gauge digital readout (DRO) was hung from a hook attached to the planer’s gear box housing. |
Planer 20 Inch General International M29 |
In Service |
|
1,944 |
| 05/19/2024 04:49 PM |
Nels Lundgren |
Missing one of the Time Shaver sanding blocks that had been used for 180 grit. |
Supplies |
Limited Functionality |
|
1,942 |
| 05/19/2024 04:19 PM |
Nels Lundgren |
The “hook lips” of the jointer push blocks were too shortleft after the new thicker neoprene was installed, so installed new “hook lips” on the push blocks |
Planer 20 Inch General International M29 |
In Service |
|
1,941 |
| 05/19/2024 04:15 PM |
Patrick Duffy |
The LED on the “Spindle Enable” button appears to be intermittant. Note that the switch does function to control the spindle. I swapped buttons with the XXL and the problem persists on the HDM. Next step is to replace the connectors at the switch to see if they are the preoblem. Next step would be to open up the VFD to see that all connections are secure. Next step would be to replace the VFD controller. |
CNC Shapeco HDM M4 |
Limited Functionality |
|
1,940 |
| 05/18/2024 12:46 PM |
Duane Kuperus |
Dust collection blast gates on both drum sanders were crossed. Starting one drum sander opened the opposite drum sander blast gate and visa versa. Spoke to Jerry M and he suggested swapping the power plugs which I did and that cleared up the problem. Labeled each power plug to the appropriate outlet. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
1,939 |
| 05/18/2024 12:05 PM |
Duane Kuperus |
Found the dust collection drums almost full. Left was 3/4 full and right was 1/2 full. This was at 11:40 AM. Shut down the shop to empty the drums. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
1,938 |
| 05/18/2024 10:44 AM |
Dan McNaughton |
The blast gates for both drum sanders are switched opposite,
need to turn on both machines to operate |
Drum Sander 25 Inch Supermax M11 |
Limited Functionality |
|
1,937 |
| 05/17/2024 02:33 PM |
Rick VanHatten |
Reinstalled manual switches. Will contact Scott S about MakeSafe control |
Belt/Disk Sander Jet M6 |
In Service |
|
1,936 |
| 05/14/2024 01:53 PM |
Rick VanHatten |
Plug from the drum motor is intermittent where it plugs into the control. Will order replacement receptacle. Works for now, when you pull the plug out about 1/8″ |
Drum Sander 25 Inch Supermax M11 |
Limited Functionality |
|
1,935 |
| 05/13/2024 01:29 PM |
Bryan Blacksher |
The M11 Drum Sander appears to have two problems:
1. The drum does not turn when the switch is activated but the feed belt does turn when its switch is activated. Does not appear to be a breaker problem. Maybe the drum switch is bad.
2. The infeed and outfeed rollers are not working as designed. The infeed roller will engage the wood until it reaches the sanding drum, then the drum raises the infeed roller so that it is no longer engaged. The outfeed roller never engages the wood. |
Drum Sander 25 Inch Supermax M11 |
Out of Service |
|
1,934 |
| 05/13/2024 10:39 AM |
Paul Schankin |
Emptied dust collection bag and vacuumed filter. Machine in service. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
1,933 |
| 05/13/2024 10:04 AM |
Paul Schankin |
Installed 90 degree fitting on second air port to minimize air hose kinking. Machine in service. |
Air Compressor Fortress |
In Service |
|
1,931 |
| 05/10/2024 09:20 PM |
Wesly Berneberg |
Backsaw fell from storage and handle broke. Taking tool to glue up handle. Return Sat 5/11. |
Hand Tools |
Out of Service |
|
1,929 |
| 05/09/2024 03:56 PM |
Phil Silverstone |
Will not turn on |
Band Saw 14 SE Laguna M3 |
Out of Service |
|
1,927 |
| 05/09/2024 03:55 PM |
Phil Silverstone |
Blade broken |
Band Saw 14-3000 Laguna M2 |
Out of Service |
|
1,926 |
| 05/08/2024 06:01 PM |
Jeff Bratt |
Guard return spring needs adjusting – the guard doesn’t reliably close after the workpiece passes through |
Jointer 12 Inch Grizzly M16 |
In Service |
|
1,925 |
| 05/08/2024 04:52 PM |
Jeff Bratt |
Current sensor on tablesaw #2 is not working right. The dust gate opens and the dust collector starts when the saw is turned on, but as soon as the blast gate fully opens it starts its 15 sec countdown to close again. And the dust collector turns off after 30 sec (short time) even though the saw is still running. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
1,924 |
| 05/05/2024 09:57 AM |
Jerry Mackelburg |
Temporary signage was added to disable automatic mode and help ensure that power is properly disabled (with the knife switch) when the dust drums aren’t sealed. |
Dust Collector 7.5 HP Oneida M14 |
Limited Functionality |
|
1,921 |
| 05/05/2024 09:51 AM |
Jerry Mackelburg |
Fuse replacement reportedly did not restore operation. |
Belt/Disk Sander Jet M6 |
Out of Service |
|
1,920 |
| 05/05/2024 09:43 AM |
Jerry Mackelburg |
Installed protective acrylic shield over Wixey thickness gauge sensor assembly. |
Planer 20 Inch General International M29 |
In Service |
|
1,919 |
| 05/04/2024 01:23 PM |
Duane Kuperus |
Auto start did not work when 16″ Laguna was operated. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
1,917 |
| 05/03/2024 11:35 PM |
Jerry Mackelburg |
I did not replace the MakeSafe fuse as was reported in Rpt.No. 1917 (which was incorrectly attributed to me.) |
Belt/Disk Sander Jet M6 |
Limited Functionality |
|
1,916 |
| 05/03/2024 11:03 AM |
Jerry Mackelburg |
Replaced Make Safe fuse. 2nd fuse in the last month. May need to change unit. Keep an eye on. |
Belt/Disk Sander Jet M6 |
In Service |
|
1,915 |
| 05/02/2024 02:36 PM |
Gordon Stone |
Motor power rating meter came loose _ cleaned area w acetone and glued meter back in place w CA glue |
Planer 20 Inch General International M29 |
In Service |
|
1,914 |
| 05/02/2024 02:32 PM |
Gordon Stone |
Circuit breaker popped while using, reset and working fine |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
1,913 |
| 05/02/2024 12:51 PM |
Lynn Welling |
power meter needs to be resecured to the machine |
Planer 20 Inch General International M29 |
In Service |
|
1,912 |
| 05/01/2024 10:38 AM |
Jerry Mackelburg |
Machine and/or MakeSafe power controller apparently still have electrical problems. |
Belt/Disk Sander Jet M6 |
Out of Service |
|
1,911 |
| 05/01/2024 10:30 AM |
Jerry Mackelburg |
Need AAA batteries. |
Supplies |
In Service |
|
1,910 |
| 05/01/2024 10:16 AM |
Jerry Mackelburg |
Yesterday Tom emptied the saw’s Fein dust extractor which was so full/clogged that the saw’s upper dust collection chute was clogged. The automatic blast gate controller on the Fein’s power cord was disconnected so it wouldn’t unnecessarily turn the Oneida dust collector on with the saw. The vertical vise, which should be used to properly/safely hold workpieces, isn’t working properly. Signage was added to it in an attempt to make it usable until it can be replaced or repaired. |
Miter Saw 12 Inch Makita M26 |
Limited Functionality |
|
1,909 |
| 05/01/2024 09:51 AM |
Jerry Mackelburg |
Circuit breaker E22 had tripped and needed to be reset during yesterday’s class. |
Drum Sander 25 Inch Supermax M10 |
In Service |
|
1,908 |
| 04/30/2024 11:50 PM |
Jerry Mackelburg |
The planing/workpiece thickness gauge was replaced with a Wixey WR550 like the one added to the new Powermatic 15″ Planer. Usage instructions for it, as well as updated planer usage instructions/guidance, was provided. The input power meter was rotated, tilted, and partially masked to improve visibility and (hopefully) clarity/utility for the operator. |
Planer 20 Inch General International M29 |
In Service |
|
1,907 |
| 04/30/2024 11:24 PM |
Jerry Mackelburg |
Rpt. No. 1904 was incorrect (it’s just different). Nels and I adjusted both the table left/right tilt and the fore/aft tilt (which the Powermatic drill press lacks) to 90 degrees. |
Drill Press 18 Inch Delta M9 |
In Service |
|
1,906 |
| 04/30/2024 05:01 PM |
Nels Lundgren |
Replaced old cutup Sacrificial Board with new foam board. It is in the sheet good rack on the end. |
Track Saw Makita |
In Service |
|
1,905 |
| 04/30/2024 05:00 PM |
Nels Lundgren |
Replenished supply of Rosin Paper, 4 rolls. Paper is in office closet. |
Supplies |
In Service |
|
1,904 |
| 04/27/2024 10:04 PM |
Jerry Mackelburg |
Unlike the Powermatic drill press, the mechanism used to adjust and clamp the table angle appears to be missing a part. |
Drill Press 18 Inch Delta M9 |
Limited Functionality |
|
1,902 |
| 04/27/2024 09:57 PM |
Jerry Mackelburg |
The motor overload protection circuit shut the unit off unexpectedly without apparent cause today during the 11:00 AM shop slot. Pressing the RESET button on the control box was necessary to restore operation. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
1,901 |
| 04/27/2024 12:34 PM |
Dana Chapin |
Paper for glue ups |
Supplies |
In Service |
|
1,899 |
| 04/25/2024 08:58 PM |
Nels Lundgren |
Replaced broken blade and tensioned using the tension gauge |
Band Saw 14-3000 Laguna M2 |
In Service |
|
1,898 |
| 04/22/2024 03:51 PM |
Jerry Mackelburg |
OOPs! it was the miter saw that had/has the vertical clamp problem – so Rpt No. 1894 was made in error. |
Track Saw Makita |
In Service |
|
1,896 |
| 04/21/2024 08:43 PM |
Jerry Mackelburg |
Rotated power meter to improve visibility somewhat (more effort is required). Covered likely unused display elements to help minimize confusion. |
Planer 20 Inch General International M29 |
In Service |
|
1,895 |
| 04/21/2024 08:11 PM |
Jerry Mackelburg |
Vertical clamp doesn’t work. |
Track Saw Makita |
Limited Functionality |
|
1,892 |
| 04/21/2024 07:56 PM |
Tom Caughlan |
1/2 spindle is bent |
Spindle Sander Enlon M33 |
Limited Functionality |
|
1,891 |
| 04/16/2024 08:39 PM |
Scott Baldwin |
I don’t know where replacement bags are kept… |
Shop Vac Rigid |
Limited Functionality |
|
1,888 |
| 04/16/2024 06:22 PM |
Sharon Sykora |
Paper towel supply replenished. |
Supplies |
|
|
1,886 |
| 04/16/2024 11:20 AM |
Paul Schankin |
Drained air tank of water, approx 1 teaspoon of water collected. Machine in service. |
Air Compressor Fortress |
In Service |
|
1,884 |
| 04/13/2024 12:28 PM |
Dana Chapin |
adjusted blade tension using tension gauge – located 13 C |
Band Saw 14-3000 Laguna M2 |
In Service |
|
1,882 |
| 04/13/2024 11:18 AM |
Dana Chapin |
accelerator for super glue – CNC supply |
Supplies |
In Service |
|
1,881 |
| 04/13/2024 10:56 AM |
Skip Florey |
Tool will not turn on |
Belt/Disk Sander Jet M6 |
Out of Service |
|
1,880 |
| 04/13/2024 10:23 AM |
Skip Florey |
Small vacuum bag will not hold vacuum. Also blue tape applied indicating OOS |
Vacuum Press |
Out of Service |
|
1,879 |
| 04/12/2024 10:21 AM |
Oi Ling Kwan |
saw blade brook, replace with new blade, tension rod needs attention |
Band Saw 14-3000 Laguna M2 |
Out of Service |
|
1,876 |
| 04/12/2024 10:09 AM |
Rick VanHatten |
Blown MakeSafe fuse. Replaced. This has happened before. No obvious cause. Keep and eye on |
Belt/Disk Sander Jet M6 |
In Service |
|
1,875 |
| 04/12/2024 09:24 AM |
Rick VanHatten |
difficulty inserting air hose fitting into compressor |
Air Compressor Fortress |
Limited Functionality |
|
1,874 |
| 04/12/2024 08:09 AM |
Paul Schankin |
DC bag at 80% full. Replaced DC bag, machine in service. |
Dust Extractor Bosch |
In Service |
|
1,873 |
| 04/11/2024 08:46 PM |
Scott Baldwin |
Sander does not come on (yes it is plugged in) Breaker is not tripped. |
Drum Sander 25 Inch Supermax M10 |
Out of Service |
|
1,872 |
| 04/11/2024 03:16 PM |
Phil Silverstone |
Previous issue with circuit breaker 41 resolved bur M 06 still not working. |
Belt/Disk Sander Jet M6 |
Out of Service |
|
1,871 |
| 04/11/2024 02:17 PM |
Patrick Duffy |
Cleared the clogged nozzle. Ran a test job with the clear PLA. Everything ran OK. |
3D Printer |
In Service |
|
1,870 |
| 04/11/2024 01:17 PM |
Phil Silverstone |
Circuit breaker A 41 to machines M06, M30 and M33 tripped and does not reset. All other breakers seem okay. |
Not a Tool Repair Issue |
|
|
1,869 |
| 04/10/2024 02:42 PM |
Patrick Duffy |
The filament has clogged the nozzle. Cause of condition was a crossover on the clear filament spool which caused the filament to not feed. Thus, the filament melted in the nozzle and “gummed: up the works. It needs an expert to clear the problem. |
3D Printer |
Out of Service |
|
1,867 |
| 04/02/2024 02:30 PM |
Rick VanHatten |
Test |
Power Hand Tools |
In Service |
|
1,862 |
| 04/01/2024 02:13 PM |
Patrick Duffy |
Repaired (?), I hope, the Spindle Enable button. The LED would not illuminate when the button was depressed. Solution: crimped the RED and BLACK connectors in the Molex connector. It seemed to fix the problem. |
CNC Shapeco HDM M4 |
In Service |
|
1,861 |
| 03/30/2024 08:00 AM |
Paul Schankin |
Focus tube was not at correct height, possible head collision. Reset to proper height. Member reported chiller “water error” and not running. Reseated power cord inlet, ran test job, no issue found. Machine in service. |
Laser Thunder Nova 51 M19 |
In Service |
|
1,859 |
| 03/29/2024 09:14 AM |
Patrick Duffy |
Dust Boot has ben replaced. |
CNC Shapeco HDM M4 |
In Service |
|
1,858 |
| 03/28/2024 09:26 PM |
Nels Lundgren |
adjusted the horizontal hold down to be parallel to the fence, so that it will hold pieces properly and applied stick um sand paper to the fence and hold down so that the piece does not raise up when the mortice bit is raised out of the cut |
Mortiser Powermatic M27 |
In Service |
|
1,856 |
| 03/26/2024 10:58 AM |
Nels Lundgren |
Replaced paper, was burnt on one end |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
1,854 |
| 03/24/2024 09:16 AM |
Duane Kuperus |
Yesterday (3/23) I had the 11AM to 2PM shift. When I arrived the previous SS had only one member in the shop during his shift. The shop cleanliness was horrible and was most likely from the Friday before and not from that morning. The floor needed sweeping, various machines were covered in saw dust, the garbage cans needed emptying, etc. Just a note for info here. |
Not a Tool Repair Issue |
In Service |
|
1,853 |
| 03/23/2024 09:55 PM |
Jerry Mackelburg |
Regarding Rpt. Nos. 1844 and 1846, the spare router was repaired, checked for excess wobble (runout), and installed in router table #2). (non-OEM brushes were installed in it.) |
Router 3.25 HP Porter Cable |
In Service |
|
1,851 |
| 03/23/2024 09:47 PM |
Jerry Mackelburg |
There’s only a couple of paper towel rolls in the restroom cabinets. |
Supplies |
Limited Functionality |
|
1,850 |
| 03/22/2024 08:56 AM |
Nels Lundgren |
Missing chuck key for Delta drill press. So down to one drill press chuck key . |
Drill Press 18 Inch Delta M9 |
In Service |
|
1,847 |
| 03/21/2024 04:11 PM |
Phil Silverstone |
Hanging outlet box above Table 2 has a “short” and should not be used until issue is resolved |
Not a Tool Repair Issue |
|
|
1,846 |
| 03/20/2024 06:46 PM |
Jeff Bratt |
Not really the dust collector, but an automated blast gate. The controller for the DeWalt planer says ‘Error’. The gate is now in manual mode. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
1,845 |
| 03/18/2024 09:08 PM |
Jerry Mackelburg |
Regarding Rpt. No. 1844, the spare router has an excessive amount of rotor radial play – “wobble”. But its brushes were in good shape, so they were used to replace those in the original router so it could be re-installed in the router table. |
Router Table #1 M30 |
In Service |
|
1,844 |
| 03/18/2024 05:03 PM |
Bryan Blacksher |
The lift plate needs to be adjusted slightly so that it is flush with the table. |
Router Table #2 Rockler M31 |
In Service |
|
1,843 |
| 03/17/2024 12:30 PM |
Nels Lundgren |
Found spare Router and replaced it into the router table. Ordered brushes for the router removed. |
Router Table #1 M30 |
In Service |
|
1,842 |
| 03/16/2024 08:23 PM |
Jerry Mackelburg |
The blast gate had been re-automated and is now working, so the “Manual” note was removed. |
Jointer 12 Inch Grizzly M16 |
In Service |
|
1,840 |
| 03/16/2024 08:13 PM |
Jerry Mackelburg |
CCTV isn’t working. |
Not a Tool Repair Issue |
Out of Service |
|
1,839 |
| 03/16/2024 08:12 PM |
Jerry Mackelburg |
Router needs to be replaced or repaired (needs new brushes). |
Router Table #1 M30 |
Out of Service |
|
1,838 |
| 03/16/2024 01:56 PM |
Dana Chapin |
Variable speed not working on high speed. Speed set to 19K. |
Router Table #1 M30 |
In Service |
|
1,837 |
| 03/15/2024 09:01 PM |
Wesly Berneberg |
Router turns ON very slowly. Take over 10 seconds to start up. |
Router Table #1 M30 |
Out of Service |
|
1,836 |
| 03/14/2024 09:20 PM |
Nels Lundgren |
Mick Bueno replaced the drum sandpaper |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
1,835 |
| 03/14/2024 09:19 PM |
Nels Lundgren |
Mick Bueno replaced the disc. |
Disk/Belt Sander Jet M38 |
In Service |
|
1,834 |
| 03/12/2024 05:23 PM |
Rick VanHatten |
Replaced broken Shroud casting. Lead time on the part is 3 months because Laguna does not stock replacement parts and they “never” break. If you work at it anything can be broken. |
Drum Sander 25 Inch Supermax M11 |
In Service |
|
1,832 |
| 03/12/2024 05:20 PM |
Rick VanHatten |
Problem with the Shades was someone changed the Channel on the Remote. Channel 1 is what the shades are on |
Not a Tool Repair Issue |
In Service |
|
1,831 |
| 03/12/2024 05:18 PM |
Rick VanHatten |
Placed In Service. Moved Sanders and related items into the drawers and update Shop Inventory to reflect. Took Down Draft Table to Storage Unit until sold & removed from Shop Log |
Sanding Station M05 |
In Service |
|
1,830 |
| 03/09/2024 08:24 PM |
Jerry Mackelburg |
The blast gate needed to be returned to manual operation. |
Jointer 12 Inch Grizzly M16 |
In Service |
|
1,828 |
| 03/02/2024 04:37 PM |
Nels Lundgren |
Adjusted the Bridge City medium and small squares to be square |
Hand Tools |
In Service |
|
1,826 |
| 03/02/2024 04:00 PM |
Jerry Mackelburg |
Shims would be handy for use with the planer sleds. |
Supplies |
In Service |
|
1,825 |
| 03/02/2024 03:58 PM |
Jerry Mackelburg |
Automatic blast gate not working reliably – changed to manual operation. |
Jointer 12 Inch Grizzly M16 |
Limited Functionality |
|
1,824 |
| 03/02/2024 12:23 PM |
Nels Lundgren |
Adjusted Miter Saw to be co-planar with the Miter Saw station table |
Miter Saw 12 Inch Makita M26 |
In Service |
|
1,823 |
| 03/02/2024 11:07 AM |
Oi Ling Kwan |
need more 0.65 in (internal diameter) sanding tubes, changed out last one on 3/2/24 |
Spindle Sander Enlon M33 |
In Service |
|
1,822 |
| 03/01/2024 09:16 AM |
Mary Russo |
saw sits about 1\16″ below the bench surface on both sides. |
Miter Saw 12 Inch Makita M26 |
In Service |
|
1,821 |
| 02/26/2024 03:35 PM |
Tom York |
The remote for the two shaded windows in the bench room doesn’t appear to work. It won’t lower the shades at the end of the shift when I hit the down button. |
Not a Tool Repair Issue |
Out of Service |
|
1,819 |
| 02/26/2024 10:43 AM |
Nels Lundgren |
Purchased more sheet sandpaper, all grits |
Supplies |
In Service |
|
1,818 |
| 02/26/2024 10:42 AM |
Nels Lundgren |
Purchased more Titebond III |
Supplies |
In Service |
|
1,817 |
| 02/25/2024 02:28 PM |
Dana Chapin |
changed blade |
Band Saw 14 SE Laguna M3 |
In Service |
|
1,816 |
| 02/24/2024 09:22 PM |
Nels Lundgren |
Automatic blast gate does not work all the time. After using it once in class demo, it did not open. Had to open manually. At the end of class tried it again and it opened, but it would not reopen until approximately 5 minutes had passed. |
Jointer 12 Inch Grizzly M16 |
Limited Functionality |
|
1,815 |
| 02/24/2024 04:23 PM |
Mark Umphres |
out of tight bond III |
Supplies |
|
|
1,814 |
| 02/24/2024 04:21 PM |
Mark Umphres |
blade broke |
Band Saw 14 SE Laguna M3 |
Out of Service |
|
1,813 |
| 02/23/2024 11:00 AM |
Rick VanHatten |
test |
Disk/Belt Sander Jet M38 |
In Service |
|
1,812 |
| 02/22/2024 09:23 AM |
Rick VanHatten |
Replaced crushed dust collection down pipe |
Lathe 1221 Jet M43 |
In Service |
|
1,810 |
| 02/21/2024 03:09 PM |
Doug Murphy |
Blast gate screw missing |
Jointer 12 Inch Grizzly M16 |
Limited Functionality |
|
1,809 |
| 02/21/2024 02:27 PM |
Doug Murphy |
Automatic dust collector gate intermittent. Opened manually |
Jointer 12 Inch Grizzly M16 |
Limited Functionality |
|
1,808 |
| 02/20/2024 09:11 AM |
Paul Schankin |
Replaced DC bag, bag at approx 75% full. Machine in service. Last date bag replace was Jan 30, 2024. |
Shop Vac Craftsman |
In Service |
|
1,805 |
| 02/20/2024 09:09 AM |
Paul Schankin |
Serviced. Drained approx 1/2 cup of water from tank. Machine in service. |
Air Compressor Fortress |
In Service |
|
1,804 |
| 02/19/2024 06:19 PM |
Mike Makowski |
Wixey Digital Angle Meter missing |
Not a Tool Repair Issue |
|
|
1,803 |
| 02/19/2024 12:05 PM |
Jerry Mackelburg |
Zeroed the exhaust backpressure gauge with 0 airflow so it will read read correctly with airflow. |
Dust Collector 7.5 HP Oneida M14 |
In Service |
|
1,800 |